Welcome, Guest. Please login or register.
November 22, 2024, 05:26:27 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  Bally Reel Games. (Moderator: a69mopar)
| | |-+  Repair - Replace reel strips		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Repair - Replace reel strips  (Read 8297 times)
litterbox99
New NLG Member 1 to 100 Post
**

Total Karma Storms: 14
Offline Offline

Gender: Male
Posts: 100
« on: February 03, 2012, 01:02:27 AM »
Just curious, I've never seen a write up on how to replace
reel strips.  I would imagine you would un-crimp the reel
cage...install new strips and re-crimp.  I'm sure it's more
complicated than that.

I don't think I would try it myself...


I'm fixing a slot for a buddy and the reel strips
are catching on the back of the reel mech.
They make the flop,flop,flop sound and slow
the reel down.

Should I try to loosen the crimp and tuck under,
then re-crimp ?

Or if I used some thin light tape to hold it down
and try to minimize weight and maintain some
kind of 'balance' ?

What have others tried ?

* strip.jpg (99.62 KB, 1012x456 - viewed 536 times.)
Logged
reho33
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 146
Offline Offline

Gender: Male
Posts: 1594


Slot Losers of America / Tokie Owens
« Reply #1 on: February 03, 2012, 01:55:50 AM »
There are no "crimps" on a reel strip. The strips are "tension fitted" under the groove in the reel basket. If done correctly, they should lay down flat and no protrusions should exist.
Logged
** NOTE: The information contained in any of my posts relating to slot machine ownership and use is information that I have gathered from publicly known sources correspondingly under the same protections of Free Speech governed under the Laws of the United States and Canada and is for informational use only. As is my Constitutional Right under United States and Canadian Laws the redistribution of said information is considered a form of free speech. Using this information in the United States or Canada to conduct illegal gambling in states/provinces where it is unlawful has been declared against the law in those states/jurisdictions and as such I do not advocate the illegal use of such information under both the United States and Canadian Laws. All references and examples of personal experiences are hypothetical in nature, and it is up to you to determine if the information presented is applicable to your situation or not**
Jim
MIDWEST SLOTS
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 288
Offline Offline

Gender: Male
Posts: 1172


513-984-2201
« Reply #2 on: February 03, 2012, 02:08:16 AM »
no its really that simple.  just try one at a time, and before you start mark where the strips start and observe how and where the crimps are.  the metal is easy to work with and you could apply too much pressure,so just take it easy.

depending how long the strips have been like that could determine how and if they will lay flat.  don't have any recommendations for that. perhaps a combination of  re-crimping and double sided tape will work.

the reels will come out of the mech. making it easier to work on.

Jim
« Last Edit: February 03, 2012, 01:16:20 PM by Jim » Logged
MIDWEST SLOTS   Selling Quality Slot Machines since 1995.  We service and repair all types of slot machines. Mills, Jennings, Bally EM, 1000/2000 series, Proslot, 6000. IGT  M, M+ ,S,  S+, S-2000,  I-Game,  Universal,  Video Poker, Sigma.
slot monkey
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 402
Offline Offline

Gender: Male
Posts: 217
« Reply #3 on: February 03, 2012, 12:49:35 PM »
I agree with the previous two posts.

From your pic it looks like all three gaps are in the same area of each reel.

Remove one reel, then remove the strip from the reel.

Peel the sticky seam apart and lay out flat.

Clean and remove the sticky from the reel ends, usually a citrus based goo cleaner works good.

Be careful and check the cleaner on a very small portion of the reel to make sure it doesn't damage the surface.

The next step is where to be careful.

After cleaning, apply a strip of double stick tape to the end edge of the strip.

The tape should not run the whole width of the strip, make it about 1/4" shorter than the reel width on each side.

Then reassemble and do the next two.

The reason for the gap to begin with is the left side of the seam was not seated against the reel track because the glue strip stopped it short on the left side.

That's why you make the double stick tape a 1/4" shorter on each side of the reel width.

Hope that helps!
Logged
litterbox99
New NLG Member 1 to 100 Post
**

Total Karma Storms: 14
Offline Offline

Gender: Male
Posts: 100
« Reply #4 on: February 04, 2012, 12:49:02 AM »
Tried to disassemble one reel cage, was very gentle.

Reel strips are very BRITTLE, cracked it a bit and
then some :-(

Ratts !

Anyone have a reel strip 234-321, or the set (321-323)
It's a wide body Bally E series.
Logged
slot monkey
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 402
Offline Offline

Gender: Male
Posts: 217
« Reply #5 on: February 04, 2012, 01:30:56 AM »
Hey litterbox

When it is hard to separate the glued edge of the reel strip, I will apply some citrus goo remover, let it sit for 20 minutes, then try to separate.

If it is still a no go, then I use an exacto knife and carefully insert it between the overlap, using it as a pry tool and working it slowly across the seam.
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #6 on: February 04, 2012, 02:32:37 AM »
Quote from: litterbox99 on February 04, 2012, 12:49:02 AM
Tried to disassemble one reel cage, was very gentle.

Reel strips are very BRITTLE, cracked it a bit and
then some :-(

Ratts !

Anyone have a reel strip 234-321, or the set (321-323)
It's a wide body Bally E series.

Take a photo of the strips laid out flat and IN THE CORRECT ORDER.
I have some laying around you can have.
Logged
litterbox99
New NLG Member 1 to 100 Post
**

Total Karma Storms: 14
Offline Offline

Gender: Male
Posts: 100
« Reply #7 on: February 05, 2012, 06:05:10 PM »
Quote from: slot monkey on February 04, 2012, 01:30:56 AM
Hey litterbox

When it is hard to separate the glued edge of the reel strip, I will apply some citrus goo remover, let it sit for 20 minutes, then try to separate.

If it is still a no go, then I use an exacto knife and carefully insert it between the overlap, using it as a pry tool and working it slowly across the seam.



I wasn't separating the overlap on the strip, I was trying
to pull one side of the cage off and crack !

I'd like to remove the strip or strips to take some pics for
replacements, but I'm afraid I'll crack some more.  

Considering I may not be able to find replacements and
that this is a 'customers' slot, I guess I'm a big chicken ;-)

I may make a text version of the strip for now.
Logged
proten
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 210
Offline Offline

Gender: Male
Posts: 1130
« Reply #8 on: February 05, 2012, 06:21:45 PM »
This is a ally E series slot right?
If that is right then you do need to get
the tools to uncrimp and crimp the strips.
There was a set on eBay.
Talk to Barry (Foxsslots) about reel strips
before you remove the old ones.
It will help realign the strips so it will pay out right.
Logged
One step at a time.
litterbox99
New NLG Member 1 to 100 Post
**

Total Karma Storms: 14
Offline Offline

Gender: Male
Posts: 100
« Reply #9 on: February 05, 2012, 06:42:29 PM »
Quote from: proten on February 05, 2012, 06:21:45 PM
This is a ally E series slot right?
If that is right then you do need to get
the tools to uncrimp and crimp the strips.
There was a set on eBay.
Talk to Barry (Foxsslots) about reel strips
before you remove the old ones.
It will help realign the strips so it will pay out right.

Yes it's a Bally E2000 wide body with the double progressive
display.  3-coin, center pay line.  Has 7's, single/double/triple
bar's and a cherry.

M1 = 755-80
M2 = 755-47
M3 = 755-48
P1 = 568279   2332-6 CTB
P2 = 002300

Strips are marked;

234-231
234-322
234-323
Logged
proten
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 210
Offline Offline

Gender: Male
Posts: 1130
« Reply #10 on: February 05, 2012, 06:45:50 PM »
PM Barry (Foxsslots) with that info and
he can tell you if the strip are available.
Logged
One step at a time.
litterbox99
New NLG Member 1 to 100 Post
**

Total Karma Storms: 14
Offline Offline

Gender: Male
Posts: 100
« Reply #11 on: February 11, 2012, 01:23:26 AM »
Foxsslots hooked me up with some new strips !

They will soon be on their way.

Any tips from those that have done this
reel strip replacment before ?
Logged
Neonkiss
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 436
Offline Offline

Gender: Male
Posts: 2084
« Reply #12 on: February 11, 2012, 01:31:29 AM »
Ya, Look at where the crimps are. Actually they were punched with like a center punch. I use a small screwdriver and open up the punch mark.
As a tip, use the sharpie marker and draw a line on the reel basket where the end of the current reel strips are. Use it as a reference for the new strips.

It's not rocket science, so don't over think it.   no  Scratch Head
Logged
Nothing brings people together better than a common enemy
343 / 60 brothers lost on that day.
litterbox99
New NLG Member 1 to 100 Post
**

Total Karma Storms: 14
Offline Offline

Gender: Male
Posts: 100
« Reply #13 on: February 15, 2012, 10:54:15 PM »
Yeah I over thunk it...

Foxsslots hooked me up with some replacements !

I took my time and it worked out well.

The slot looks so fresh now :-)
Logged
kforeman
Today...Slot Tech Tomorrow...Still be a Tech
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 42
Offline Offline

Gender: Male
Posts: 378
« Reply #14 on: February 16, 2012, 02:24:00 AM »
Quote from: litterbox99 on February 15, 2012, 10:54:15 PM
Yeah I over thunk it...

Foxsslots hooked me up with some replacements !

I took my time and it worked out well.

The slot looks so fresh now :-)

Sweet!!  Dancing Party Dancing Party even though i didn't post i was following this discussion so  +1 (Karma, or whatever) for letting us know how it worked out! Thanks
Logged
Now You're Techin'!!!
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.096 seconds with 20 queries.