E3 on Mikohn in Bally 6000

[FORDSBS]

I put a Mikohn on a Bally 6000. I get E3 code. Rolls up credits OK.
Error codes are all C?
Thanks for help, Ford
<a href="http://www.youtube.com/v/N1yoqcgBftQ&rel=0" target="_blank">http://www.youtube.com/v/N1yoqcgBftQ&rel=0</a>

[knagl]

Interesting.

According to the manual for the Supreme, E3 is "EEPROM WRITE ERROR".  I'm guessing that you don't have a Supreme behind the glass there, but it's likely that Mikohn used the same error codes accross their platforms.

[FORDSBS]

It's a cam II. Would that be an eprom in the Mikohn or in the slot? The machine works OK.

I must have something set wrong.

[FORDSBS]

Tonight going to swap harness with one that is working & see if that helps

[FORDSBS]

Swapped wire & no change.
Put another Mikohn in & OK. When have time will have to start setting it up again from scratch.
Thanks Ford

Just remembered that I was pissing around trying to get message in it the other day & something with that might be problem.

[FORDSBS]

How do I clear all off to start over?
Thanks Ford

[stormrider]

How do I clear all off to start over?
Thanks Ford

Unplug the power cord at the power supply
Then hold down the 2 buttons next to the switch
on the chamII+ board while holding them insert the power cord back in.
The display should flash a few times....then let go.
This will reset it,then put all the correct values back in on the chamII
using the switch and buttons.

If this doesn't work then I suggest replacing U19 on the chamII board
it should be a 27c2001 or 27c020 off the top of my head.

I don't think you have a E3 error but a C3
somehow its corrupt...start from scratch and post back results...

Good Luck. Tim

[FORDSBS]

Thanks Tim, Just tried, got flash, reprogrammed it & same with E3
Guess bad chip

[stormrider]

After watching the video and you saying about messing around with a message input
It looks to me the display is trying to switch back from jackpot value to a message.
Maybe you have a jackpot.do file setup in psp wrong...
Reset the whole thing and start over with psp not using the last config

[FORDSBS]

Did the pull plug & get flashing.
Comes up with E3
Reprogrammed with different amounts & still get E3

[stormrider]

Did the pull plug & get flashing.
Comes up with E3
Reprogrammed with different amounts & still get E3

I'd love to help you more on this but I'm off to bed
try replacing the U19 and start over is all I can suggest.

If you get to the point where you want to throw it up against the wall...DON'T  
Send it to me and I'll fix it at no cost.....

Have a good night Ford
and will talk more tomorrow.

Tim


Oh make sure the battery voltage is good if it falls below 2.8
I've seen different errors.

[FORDSBS]

Thanks Tim.
I'll copy chip from another working one I have & try that in the U19
Ford

[FORDSBS]

copied U19 & tried. Same thing

[FORDSBS]

Thanks Tim, 
When I was clearing did not move sw2. Moved sw2 & it cleared with E3 still there.
Programmed it & NO MORE E3.
Thanks again, Ford
  p.s.   THANKS FOR OFFER TO FIX FOR ME.

Now I have to read,read & read some more on how to put message in.

[stormrider]

Thanks Tim,  
When I was clearing did not move sw2. Moved sw2 & it cleared with E3 still there.
Programmed it & NO MORE E3.
Thanks again, Ford
  p.s.   THANKS FOR OFFER TO FIX FOR ME.

Now I have to read,read & read some more on how to put message in.

Good job Ford  
I was going to call you when I got home from work.

Yes you have some reading to do on the message input.
Better throw a spare setup on the bench and start playing
many settings come into play on getting it to work right.
You might want to do a search on this as this has been discussed in the past,
of course you can always call me if you get stuck..It's a real hair puller the first time.

  back at ya

Tim

[FORDSBS]

Thanks Tim, Shutting down, getting one he** of a storm

Could not have done it without your help !!!

[FORDSBS]

Turned on this morning & E3 again. Cleared & reset & OK.
I think problem is I have a message that it's looking for & this dummy did not set it up correct.
Have to find a way to delete message hanging in there.

[stormrider]

Turned on this morning & E3 again. Cleared & reset & OK.
I think problem is I have a message that it's looking for & this dummy did not set it up correct.
Have to find a way to delete message hanging in there.

Ford,

Are you still stuck on this ?
My question to you is when you cleared the cham board
then used psp to set it back up, did you use the same configuration as last time ?
meaning did you save it from the last time you were messing around with a message
and just reloaded it,If so you need to start fresh with psp.

Go into the main psp page "Jackpot Display Configuration"
Select #4 Message Programming
You will then see 1-7

The only one that should show a message is #7 DEMO.DO
Do Not I repeat DO NOT clear that message.
Just have a look inside each one use F10 to back out
without messing it up.

If you do find a message in any between 1-6
this could be your problem.

Just thought i would pass this along.

Tim

One other thing you don't have the cham board set up as MFILE 0 by chance do ya ?

[FORDSBS]

Every time I start it up The E3 is there. I clear it and use different configuration & it's OK until I turn
it off overnight.
I have it @ the shop.
Today I did what you said I SHOULD NOT.  I CLEARED THE MESSAGE. Guess I'll see what it's like when
I go to work tomorrow.
I have MFILE @ 4

[stormrider]

Every time I start it up The E3 is there. I clear it and use different configuration & it's OK until I turn
it off overnight.
I have it @ the shop.
Today I did what you said I SHOULD NOT.  I CLEARED THE MESSAGE. Guess I'll see what it's like when
I go to work tomorrow.
I have MFILE @ 4

Okay let me know how you make out
Also #5 JPOT.DO should not be cleared
sorry long day at work....I think I need a beer.

[FORDSBS]

Will see tomorrow & let you know.
Pop a cool one for me. 
Ford

[FORDSBS]

Got the best of me. Went to shop & E3 comes up again.
Maybe I didn't clear it right. HOPE SO.
If there's something in 1-6 what do I do with it?

[knagl]

I'd strongly suspect that the EEPROM on the board is bad.  It works until the board tries to write data (as a backup), and then realizes there's a problem and gives you an E3.

[FORDSBS]

I made copy of U19 chip from a working one & tried it, same thing.

[a69mopar]

did you try swapping the the U4? this is the ram. or the U5 this is the flash memory.
The U19 is an EPROM (Electronically Programmable Read Only Memory), which can't be written to by the controller.
Thanks,
Wayne