Welcome, Guest. Please login or register.
October 31, 2024, 09:20:32 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  Bally Electromechanical
| | |-+  help and advice
0 Members and 1 Guest are viewing this topic. « previous next »
Pages: 1 [2] Go Down Print
Author Topic: help and advice  (Read 12255 times)
OldReno
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 175
Offline Offline

Gender: Male
Posts: 818



« Reply #25 on: April 02, 2013, 06:50:52 PM »

Your high pays are already there, they are soldered at the bottom of the board, with jumpers going to where they should.  What does the magic is the two sets of outboard wiper fingers which make contact with the feed ring after you put them back on.  They are your high pay circuits.  You should be good to go once you run that jumper on the feed....
Logged
mark the spark
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 16
Offline Offline

Gender: Male
Posts: 154



« Reply #26 on: April 03, 2013, 05:48:06 AM »

there is more info i have only just sorted.the 50 pay on the hopper had three wires on it colour wise 43 54 and 81
assuming 43 is the 50 pay and can stay on that terminal
81 appears to be 100 feed and can go on the 100 feed at the bottom so 54 can either be 150 or 200 but the terminal at the bottom is 150 but there is no 150 payout so  can
we solder this to the 200 terminal on the bottom left hand side of the board on the 200 terminal
Logged
mark the spark
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 16
Offline Offline

Gender: Male
Posts: 154



« Reply #27 on: April 05, 2013, 10:11:26 AM »

thanks once again to all, Clap machine is now running and paying out although there was a problem on the 200 pay where the carriage arm ran into the switch stack
causing the house electrics to trip, her indoors was not best pleased especially as i lied like a cheap watch and said nothing to do with me but after the second time it happened i had to hold my hands up!!!
will now tidy up the wiring on the hopper clean it up and then will be looking for suggestions about repairing/replacing some artwork on the glass
Logged
mark the spark
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 16
Offline Offline

Gender: Male
Posts: 154



« Reply #28 on: April 27, 2013, 12:35:43 PM »

thanks to all this project is all but finished just some cosmetic touches when the right materials come along
just the coin in meter not working and had to disconnect the door switch as the mount wouldn`t fit with the hopper
but all small stuff  really so its onto the next project a 742 penny star so will be starting a new thread soon
Logged
Pages: 1 [2] Go Up Print 
« previous next »
Jump to:  


If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com    Newlifegames.net    Newlifegames.org
   New Life Games    NewLifeGames  NLG  We Bring new Life to old Games    1-888-NLG-SLOTS
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.076 seconds with 19 queries.