Welcome, Guest. Please login or register.
November 21, 2024, 11:58:23 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  IGT S2000 and Vision Games.
| | |-+  IGT S-2000 ERROR (Display's NETPLEX Link is Down)		 0 Members and 2 Guests are viewing this topic. « previous next »
Pages: [1] 2 Go Down Print
Author Topic: IGT S-2000 ERROR (Display's NETPLEX Link is Down)  (Read 58366 times)
Slottex
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 120
Offline Offline

Gender: Male
Posts: 146
« on: February 15, 2009, 11:29:57 AM »
Display's NETPLEX Link is Down , I CHECKED CONNECTIONS ALSO REPLACED WITH KNOWN GOOD POWER SUPPLY ANY IDEA WHAT IS CAUSING THIS ????

THANKS DANNY  Scratch Head
Logged
Ron (r273)
NLG Welcome Wagon & General Chat
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 401
Offline Offline

Gender: Male
Posts: 1819
« Reply #1 on: February 15, 2009, 12:04:23 PM »
Might try reading some posts though the search button at the top of the page, "Nexplex link down"

Ron
Logged
idesign
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 509
Offline Offline

Gender: Male
Posts: 1456


If it aint broke why mess with it?????
« Reply #2 on: February 15, 2009, 12:30:27 PM »
Is this on boot up or did it happen after the machine was up and running?
Logged
Slottex
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 120
Offline Offline

Gender: Male
Posts: 146
« Reply #3 on: February 15, 2009, 12:59:47 PM »
THIS HAPPENED ON BOOT UP! THIS IS AS ANOTHER MACHINE I BOUGHT THAT I AM SHOPPING OUT. I CHANGED THE MPU BOARD AND EVERYTHING IS WORKING FINE. I GUESS THIS CAN COME UP IN A BAD BOARD ?  ANY THOUGHTS IS STILL APPRECIATED !

THANKS DANNY
Logged
idesign
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 509
Offline Offline

Gender: Male
Posts: 1456


If it aint broke why mess with it?????
« Reply #4 on: February 15, 2009, 01:02:43 PM »
I have come across several bad boards that do that.  Another common bad board error is a coin-in jam.  Tracing out the bad component is nearly impossible.
Logged
Slottex
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 120
Offline Offline

Gender: Male
Posts: 146
« Reply #5 on: February 15, 2009, 01:36:02 PM »
THANKS FOR THE REPLY & KARMA TO YOU!!!!

THANKS
Logged
dpalmi
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 291
Offline Offline

Gender: Male
Posts: 819



WWW
« Reply #6 on: February 15, 2009, 04:57:18 PM »
Quote from: SLOTTEX on February 15, 2009, 11:29:57 AM
Display's NETPLEX Link is Down , I CHECKED CONNECTIONS ALSO REPLACED WITH KNOWN GOOD POWER SUPPLY ANY IDEA WHAT IS CAUSING THIS ????


Hello!

When you say you replaced the power supply, did you replace the one behind the reels?  This is usually the cause of the problem.  Check the thread's I've listed below for more info...

http://newlifegames.net/nlg/index.php?topic=960.0
http://newlifegames.net/nlg/index.php?topic=1885.msg13726

Dan #2
Logged
A great man once said, "I was told last time I would get a piece of cake."
idesign
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 509
Offline Offline

Gender: Male
Posts: 1456


If it aint broke why mess with it?????
« Reply #7 on: February 15, 2009, 05:11:53 PM »
Quote from: dpalmi on February 15, 2009, 04:57:18 PM
Quote from: SLOTTEX on February 15, 2009, 11:29:57 AM
Display's NETPLEX Link is Down , I CHECKED CONNECTIONS ALSO REPLACED WITH KNOWN GOOD POWER SUPPLY ANY IDEA WHAT IS CAUSING THIS ????


Hello!

When you say you replaced the power supply, did you replace the one behind the reels?  This is usually the cause of the problem.  Check the thread's I've listed below for more info...

http://newlifegames.net/nlg/index.php?topic=960.0
http://newlifegames.net/nlg/index.php?topic=1885.msg13726

Dan #2



He fixed the problem by replacing the mpu.
Logged
Railroad94
In Remembrance of our lost NLG Members
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 225
Offline Offline

Gender: Male
Posts: 585
« Reply #8 on: February 15, 2009, 05:18:17 PM »
U-67 seems to be a common componet that gets blown on the boards, Have seen a few and you can see the hole in it.

I'm sure idesign thanks you for the K+   looks like he can use it    bust gut laughing
Logged
idesign
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 509
Offline Offline

Gender: Male
Posts: 1456


If it aint broke why mess with it?????
« Reply #9 on: February 15, 2009, 05:22:06 PM »
Quote from: Railroad94 on February 15, 2009, 05:18:17 PM
U-67 seems to be a common componet that gets blown on the boards, Have seen a few and you can see the hole in it.

I'm sure idesign thanks you for the K+   looks like he can use it    bust gut laughing


Yea, like I really need more karma..........anybody want to purchase some of my extra bust gut laughing bust gut laughing karma.....I seem to be topped out at the moment.  bust gut laughing bust gut laughing bust gut laughing
Logged
StatFreak
rotaredoM etiS GLN labolG
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 756
Offline Offline

Gender: Male
Posts: 8549


Warning! Spammers will be eaten, with relish!
« Reply #10 on: February 15, 2009, 09:20:24 PM »
Quote from: idesign on February 15, 2009, 05:22:06 PM
....I seem to be topped out at the moment.  bust gut laughing bust gut laughing bust gut laughing

 bust gut laughing bust gut laughing bust gut laughing  I gave you a single K-, so now SLOTTEX can give you the positive that he wanted to. rotflmao rotflmao rotflmao
Logged
I found myself at NLG garfield  ..but got lost again on the way home. Scratch Head 2
If found, please email me to myself. Thanks. yes
       Executive member in good standing of Rick's SMAA.                              Ehhh...What's Up Doc?
idesign
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 509
Offline Offline

Gender: Male
Posts: 1456


If it aint broke why mess with it?????
« Reply #11 on: February 15, 2009, 09:27:27 PM »
Darn it David, I gave you +1 and look what happened?  We must be running a special on karma today 33000 for the price of 1........ bust gut laughing bust gut laughing bust gut laughing bust gut laughing bust gut laughing
Logged
StatFreak
rotaredoM etiS GLN labolG
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 756
Offline Offline

Gender: Male
Posts: 8549


Warning! Spammers will be eaten, with relish!
« Reply #12 on: February 16, 2009, 12:32:40 AM »
Quote from: idesign on February 15, 2009, 09:27:27 PM
Darn it David, I gave you +1 and look what happened?  We must be running a special on karma today 33000 for the price of 1........ bust gut laughing bust gut laughing bust gut laughing bust gut laughing bust gut laughing

I should have known better than to mess with the big boys!  Duh! Duh! slap
I gave you your K+ back.  Hail  I even dusted it off for you and put it right back on the doily on the mantle where I found it.  Wasn't Me
Logged
I found myself at NLG garfield  ..but got lost again on the way home. Scratch Head 2
If found, please email me to myself. Thanks. yes
       Executive member in good standing of Rick's SMAA.                              Ehhh...What's Up Doc?
SAT (aka GANDHI)
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 224
Offline Offline

Gender: Male
Posts: 807
« Reply #13 on: February 17, 2009, 11:31:08 AM »
It happened to me that the display driver board was the faulty one... I confirmed it by swapping this board with a working machine.

I'm attaching two pictures of it for you to see both the board and the part #.

Regards!

(BTW: this board is installed in the main door and it's normally covered with a sort of metallic or plastic plate)

* IMAG0168.jpg (918.23 KB, 1536x2048 - viewed 1876 times.)

* IMAG0169.jpg (855.39 KB, 1536x2048 - viewed 1530 times.)
Logged
Keep it simple!!!
kforeman
Today...Slot Tech Tomorrow...Still be a Tech
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 42
Offline Offline

Gender: Male
Posts: 378
« Reply #14 on: February 17, 2009, 02:36:01 PM »
the board SAT put a picture up of is the vacuum fluorescent display(VFD) driver board.  not a common failure but happens occasionally, there is a surface mount cap that has been the problem 4 out of 5 times for us.  i can't remember the value off the top of my head, but i believe it is designated as C3 on the board.

also on an S2000 the netplex components are your Bill Validator, Thermal Printer, VFD, 7 Seg, and Spectrum Display.  a problem with either of these can take netplex down.

that being said, probably 95% of our 'netplex link down' errors in the past 3 years have been due to the DC switching power supply behind the reels.  we have been repairing them for probably 2 years by shotgunning electrolytic caps with a 85-90% repair rate.

edit:  the value on the surface mount cap for the VFD driver board is 4.7uf, 16V
« Last Edit: February 17, 2009, 10:52:25 PM by kforeman » Logged
Now You're Techin'!!!
idylewild1
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 140
Offline Offline

Gender: Male
Posts: 591



WWW
« Reply #15 on: February 17, 2009, 10:19:45 PM »
A way to check this is to make a test rig out of an extension cord. Cut the recepticle end of the extension cord off and crimp on connectors that will fit the pins in the power supply. Contect line voltage to pin 24 and 22 and connect ground to pin 11. Plug into any outlet. Now measure voltage using pin 17 as ground for your meter. Pin 1,2 and 13 should read 13V. Pin 3,14,and 15 should read 25V. Pin 7 should read 5-7V. Pin 7 is used for a logic signal. If all the voltages except pin 7 are present you will get the infamous "display netplex link down" error. On he win-tact power suppies this usually indicates circuit board 2 is defective.
Logged
idylewild1

http://samronslots.com/
kforeman
Today...Slot Tech Tomorrow...Still be a Tech
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 42
Offline Offline

Gender: Male
Posts: 378
« Reply #16 on: February 17, 2009, 10:55:31 PM »
Quote from: idylewild1 on February 17, 2009, 10:19:45 PM
A way to check this is to make a test rig out of an extension cord. Cut the recepticle end of the extension cord off and crimp on connectors that will fit the pins in the power supply. Contect line voltage to pin 24 and 22 and connect ground to pin 11. Plug into any outlet. Now measure voltage using pin 17 as ground for your meter. Pin 1,2 and 13 should read 13V. Pin 3,14,and 15 should read 25V. Pin 7 should read 5-7V. Pin 7 is used for a logic signal. If all the voltages except pin 7 are present you will get the infamous "display netplex link down" error. On he win-tact power suppies this usually indicates circuit board 2 is defective.

nice...i see myself destroying a perfectly functional power cord today in the name of testing!!
Logged
Now You're Techin'!!!
Railroad94
In Remembrance of our lost NLG Members
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 225
Offline Offline

Gender: Male
Posts: 585
« Reply #17 on: February 17, 2009, 11:00:06 PM »
Christmas is over so cut away bust gut laughing
idylewild,nice breakdown on the P.S.     applause   K+ to ya
Logged
Foster
The S2000 GURU
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 345
Offline Offline

Gender: Male
Posts: 2872
« Reply #18 on: February 18, 2009, 12:28:39 AM »
How can one tell by looking at the PS (with the cover removed) if they have a good version compared to a troublesome version?
Logged
A Slot Machine and Coca-Cola Addict!!
"If it is not broke do not fix it" I keep forgetting that!
kforeman
Today...Slot Tech Tomorrow...Still be a Tech
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 42
Offline Offline

Gender: Male
Posts: 378
« Reply #19 on: February 18, 2009, 12:29:48 AM »
i have cut, i have connected, now i have tested!!  much easier than installing in a machine to test.  thanks again idylewild1 Hail
Logged
Now You're Techin'!!!
idylewild1
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 140
Offline Offline

Gender: Male
Posts: 591



WWW
« Reply #20 on: February 18, 2009, 09:20:30 PM »
I have a work around for the "display netplex link down" error on Win-Tact WP203F11 power supplies. I was tired of throwing them away or finding some components iimpossible to get. First make sure that all three +13V and all three +25V outputs are present and that pin 7 is zero volts. The test procedure above works great for this. This means that the logic siginal is missing form the power supply. If pin 7 is above +3V it is concidered a logic 1 or high -- if it is 0V it is considered a 0 or low.

The work around is to break the connection from pin 7 to pin 13 of the Ctr Bd 2 as shown in the attached picture. I do this with a srew driver or knife and just cut through the lan. The last thing is connect a wire from pin 5 of the CTR BD 2 to pin 7 on the output connector. This is done on the backside of the circuit board. This is using +5V VCC for the logic siginal. This is also shown in one of the pictures.

If you have a win-tact power supply in this shape you might want to give it a try. I have done 10 and they are still ticking.

* WP.jpg (94.52 KB, 1231x1568 - viewed 2301 times.)

* WP1.jpg (93.96 KB, 1209x1572 - viewed 2140 times.)
Logged
idylewild1

http://samronslots.com/
kforeman
Today...Slot Tech Tomorrow...Still be a Tech
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 42
Offline Offline

Gender: Male
Posts: 378
« Reply #21 on: February 19, 2009, 12:00:26 AM »
Quote from: idylewild1 on February 18, 2009, 09:20:30 PM
I have a work around for the "display netplex link down" error on Win-Tact WP203F11 power supplies. I was tired of throwing them away or finding some components iimpossible to get. First make sure that all three +13V and all three +25V outputs are present and that pin 7 is zero volts. The test procedure above works great for this. This means that the logic siginal is missing form the power supply. If pin 7 is above +3V it is concidered a logic 1 or high -- if it is 0V it is considered a 0 or low.

The work around is to break the connection from pin 7 to pin 13 of the Ctr Bd 2 as shown in the attached picture. I do this with a srew driver or knife and just cut through the lan. The last thing is connect a wire from pin 5 of the CTR BD 2 to pin 7 on the output connector. This is done on the backside of the circuit board. This is using +5V VCC for the logic siginal. This is also shown in one of the pictures.

If you have a win-tact power supply in this shape you might want to give it a try. I have done 10 and they are still ticking.

awesome, thanks for the info and the great pics to go with...i believe i have one in the shop now to try this on.
Logged
Now You're Techin'!!!
ALLEN47
Guest
« Reply #22 on: May 05, 2009, 12:40:21 PM »
ON THE WNTACT POWER SUPPLIES THERE ARE SEVERAL VOLTAGE DETECTING,SYSTEM RESETTING IC'S M51957XXX.  ONTHE WP203F11 THE IC FOR THE NETPLIX ERROR IS LOCATED ON THE CONTROL 2 BOARD (CTR2) AND IS IC4.  WHILE YOU HAVE THIS BOARD OUT YOU MIGHT AS WELL CHANGE Q3 AND THE ELECTROLYTIC CAPS.  iF YOU NEED MORE HELP I HAVE THE SCHEMATICS FOR THE 203, 206, AND 207 UNITS. 

Glenn

gallen@threeriverscasino.com
  
« Last Edit: May 05, 2009, 01:42:58 PM by ALLEN47 » Logged
Bettor Slots
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 751
Offline Offline

Gender: Male
Posts: 1946



WWW
« Reply #23 on: May 05, 2009, 01:36:19 PM »
Very nice post Ron...thanks.

Jim
Logged
If life is like a box of chocolates....why do I always seem to end up with the butter creme?
woilly
Guest
« Reply #24 on: October 28, 2011, 06:47:43 PM »
Quote from: Railroad94 on February 15, 2009, 05:18:17 PM
U-67 seems to be a common componet that gets blown on the boards, Have seen a few and you can see the hole in it.

I'm sure idesign thanks you for the K+   looks like he can use it    bust gut laughing

Do you mean the 3 pins smt chip that seems to be a regulator?
Logged
Pages: [1] 2 Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.108 seconds with 19 queries.