Welcome, Guest. Please login or register.
November 22, 2024, 06:27:45 AM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  Bally Reel Games. (Moderator: a69mopar)
| | |-+  Bally Pro Slot - Help		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Bally Pro Slot - Help  (Read 10124 times)
funtime1
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Gender: Male
Posts: 32
« on: September 24, 2012, 10:29:09 AM »
My slot stopped working about a month ago. It was working then it stopped. The lights come on but nothing else. I keep reading POWER SUPPLY issues are common. Any suggestion on how to test and where to purchase? Many thanks in advance

* Bally - California Dreams Slot Machine.JPG (1573.09 KB, 3072x2304 - viewed 390 times.)
« Last Edit: October 02, 2012, 11:19:21 PM by funtime1 » Logged
a69mopar
647-402-1977
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 600
Offline Offline

Gender: Male
Posts: 3508



WWW
« Reply #1 on: September 24, 2012, 10:24:20 PM »
Blueridgeslots had the power supplies.  you can check for voltages with a meter.  they were a weak link on the earlier machines.

you should fill out your profile so that people will know what area of the world you are in..  you may have a neighbour that has the parts.

thanks,
Wayne
Logged
         www.GTASLOTS.com      647-402-1977              BALLY S6000 GALLERY
funtime1
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Gender: Male
Posts: 32
« Reply #2 on: September 25, 2012, 10:41:12 AM »
Wayne,

Thanks for your response! I looking for a schematic but have not had any luck. I also updated my profile. Again thank you for your help.
Jonathan
Logged
paul
paul
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 20
Offline Offline

Gender: Male
Posts: 548
« Reply #3 on: September 25, 2012, 05:03:53 PM »
I think raz410 has them also
Logged
funtime1
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Gender: Male
Posts: 32
« Reply #4 on: October 02, 2012, 11:19:47 PM »
UPDATE: Purchased Power Supply from Rudy's Deals and installed today. I think the power supply is either damaged or incorrect the light on the mpu board is very dim and the hopper is pulsating. If I push the hopper buttom the green and the red work but no displays. Any suggestions? I am about to pull what little hair I have left out.
Logged
solinoid
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 25
Offline Offline

Gender: Male
Posts: 66
« Reply #5 on: October 04, 2012, 01:06:26 AM »
Jonathan,
Here's a link to a manual. Check out the other goodies here also!

http://slot-tech.com/interesting_stuff/bally/ProSlot/

Barry
Logged
If it ain't broke don't fix it. If it is , give me a crack at it Smiley
funtime1
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Gender: Male
Posts: 32
« Reply #6 on: October 05, 2012, 02:25:49 AM »
Barry,
Thanks Alot!

Update - Contacted Rudy's Deals - Going to send out another power supply - GREAT CUSTOMER SERVICE!!!!!!!!!!!!!!!!!!!!!

I am determined to fix this. To everyone that is responding....THANK YOU!

I am going to write a book... " Slots For Dummies" LOL
Logged
funtime1
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Gender: Male
Posts: 32
« Reply #7 on: October 10, 2012, 11:20:04 PM »
Update: Rudy's sent another power supply. Thanks again for the great customer service!!! Now everything powers up and if you guess I got codes you are correct. One is 5.0 which is door switch and other is 7.3 reel movement. I have check the wiring am I am sure that I am not missing anything and the switches are good. Any suggestions? I am almost bald.

Thanks in advance
Logged
paul
paul
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 20
Offline Offline

Gender: Male
Posts: 548
« Reply #8 on: October 10, 2012, 11:30:06 PM »
Clear machine
Logged
FORDSBS
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 363
Offline Offline

Gender: Male
Posts: 4162


PET
« Reply #9 on: October 10, 2012, 11:44:31 PM »
Quote from: paul on October 10, 2012, 11:30:06 PM
Clear machine

HE'S CORRECT
Logged
funtime1
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Gender: Male
Posts: 32
« Reply #10 on: October 11, 2012, 01:24:08 PM »
Thank you for the response. How do I clear the machine. Sorry I am the "FNG"!
Logged
FORDSBS
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 363
Offline Offline

Gender: Male
Posts: 4162


PET
« Reply #11 on: October 11, 2012, 01:27:23 PM »
You need U28 & U43 clear chips
Logged
funtime1
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Gender: Male
Posts: 32
« Reply #12 on: October 11, 2012, 01:51:42 PM »
Where can I get U28 & U43 clear chips?
Logged
FORDSBS
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 363
Offline Offline

Gender: Male
Posts: 4162


PET
« Reply #13 on: October 11, 2012, 01:52:40 PM »
jj slots had some
http://jjslots.com/
Logged
stormrider
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 131
Offline Offline

Gender: Male
Posts: 772
« Reply #14 on: October 11, 2012, 02:14:48 PM »
I never had to clear the machine to get rid of the 73 error.. open the door and hold the change switch and shut the door.the reels well realign and should clear the 73. open and shut the door again and that should clear the 50.. hope this helps tried sending this from my cellphone
Logged
FORDSBS
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 363
Offline Offline

Gender: Male
Posts: 4162


PET
« Reply #15 on: October 11, 2012, 02:36:50 PM »
That's worth a try
Logged
stormrider
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 131
Offline Offline

Gender: Male
Posts: 772
« Reply #16 on: October 11, 2012, 03:45:57 PM »
I would also check the reel harness to the backplane
 make sure it's fully seated.. since you change the power supply you might have jarred something loose
Logged
FORDSBS
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 363
Offline Offline

Gender: Male
Posts: 4162


PET
« Reply #17 on: October 11, 2012, 04:19:20 PM »
funtime1, did you get it working?
Did you try what stormrider told you?
Logged
nousmeme
New NLG Member 1 to 100 Post
**

Total Karma Storms: 4
Offline Offline

Posts: 22
« Reply #18 on: October 11, 2012, 05:20:43 PM »
Quote from: funtime1 on October 11, 2012, 01:51:42 PM
Where can I get U28 & U43 clear chips?
Hi Funtime1, can you send me a picture of your MPU? Maybe I can help you to clear the machine without clear chips.
Logged
paul
paul
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 20
Offline Offline

Gender: Male
Posts: 548
« Reply #19 on: October 11, 2012, 07:14:06 PM »
change 3-4-12-15  to 920000 you never need clears again just a jumper check and see the series on those chips
Logged
funtime1
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Gender: Male
Posts: 32
« Reply #20 on: October 19, 2012, 12:37:25 PM »
Update: Thanks to everyone for their help! I had to go out of town but I am planning on working on it this weekend. So everyone keep their fingers crossed!
Logged
funtime1
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Gender: Male
Posts: 32
« Reply #21 on: October 20, 2012, 09:39:45 PM »
Update - I did a partial reset and it cleared the code 73 but 50 was still present. I rechecked all door switches and found the blade switch on the top door not was not closing the circuit properly so I replaced it and NOW IT IS FIXED!!!!!!!!!!!!!!!

Thanks again for everyone advise and words of encouragement!
Logged
paul
paul
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 20
Offline Offline

Gender: Male
Posts: 548
« Reply #22 on: October 21, 2012, 12:17:24 AM »
Good too see you fixed it good luck   Paul
Logged
funtime1
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Gender: Male
Posts: 32
« Reply #23 on: October 21, 2012, 01:05:05 AM »
Thanks Paul !
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.122 seconds with 20 queries.