Welcome, Guest. Please login or register.
November 22, 2024, 08:36:55 AM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  Bally Reel Games. (Moderator: a69mopar)
| | |-+  Balley E2332-1		 0 Members and 2 Guests are viewing this topic. « previous next »
Pages: [1] 2 Go Down Print
Author Topic: Balley E2332-1  (Read 9791 times)
drfreeze1739
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 16
Offline Offline

Gender: Male
Posts: 432


drfreeze1739@sbcglobal.net
« on: November 18, 2012, 10:22:53 PM »
Hello all.

Need a little help on this one,,,,

It powers on and it shows 50 in the lcd.  but the coin mec on the door wont energize and it shows tilt.

I go to the rest switch on the hopper and reset it it and it will energixe for a split sec then deenergize and then back into tilt mode.

i have ran the self test and the hopper works in the test. the coil test works.. ran the switch test and perss the coin in switch and it will change the lcd numbers.

when i run the reel test the lcd just shows 1.1.1


I cant get it to work other than doing the test...

Any help????

Will post pics in a min..
Logged
Mark
drfreeze1739
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 16
Offline Offline

Gender: Male
Posts: 432


drfreeze1739@sbcglobal.net
« Reply #1 on: November 18, 2012, 10:31:19 PM »
pics

* 100_4693.JPG (490.14 KB, 2048x1536 - viewed 281 times.)

* 100_4694.JPG (494.78 KB, 2048x1536 - viewed 306 times.)
Logged
Mark
drfreeze1739
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 16
Offline Offline

Gender: Male
Posts: 432


drfreeze1739@sbcglobal.net
« Reply #2 on: November 18, 2012, 10:35:19 PM »
pics

* 100_4695.JPG (456.02 KB, 1536x2048 - viewed 317 times.)

* 100_4697.JPG (487.65 KB, 2048x1536 - viewed 293 times.)
Logged
Mark
drfreeze1739
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 16
Offline Offline

Gender: Male
Posts: 432


drfreeze1739@sbcglobal.net
« Reply #3 on: November 18, 2012, 10:36:34 PM »
pics

* 100_4698.JPG (488.49 KB, 2048x1536 - viewed 274 times.)

* 100_4700.JPG (517.02 KB, 2048x1536 - viewed 281 times.)
Logged
Mark
drfreeze1739
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 16
Offline Offline

Gender: Male
Posts: 432


drfreeze1739@sbcglobal.net
« Reply #4 on: November 18, 2012, 10:39:13 PM »
pics

* 100_4699.JPG (505.56 KB, 2048x1536 - viewed 299 times.)

* 100_4703.JPG (473.4 KB, 2048x1536 - viewed 299 times.)
Logged
Mark
tkrozleski
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 23
Offline Offline

Gender: Male
Posts: 308
« Reply #5 on: November 19, 2012, 09:26:16 PM »
Have you reseated all the wiring harnesses to all the boards?
Reseated all the IC's on all the boards?
Fuses and fuse holders are all good?
Voltages to all the test points on all the boards are good?
Battery is good?
I have found that directly below the battery, the IC and socket in the U30 position sometimes gets severely corroded from the battery.
Logged
drfreeze1739
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 16
Offline Offline

Gender: Male
Posts: 432


drfreeze1739@sbcglobal.net
« Reply #6 on: November 19, 2012, 09:33:31 PM »
I have unpluged and repluged in every connector on the door and on all the boards.

i have checked all the fuse's

I put 2 AA batterys in place of the one that was on the board temp for now.

I have pulled all reseated just about all the main chips.. But not all yet.

I havent checked the voltage yet.. Doing that tonight...
Logged
Mark
litterbox99
New NLG Member 1 to 100 Post
**

Total Karma Storms: 14
Offline Offline

Gender: Male
Posts: 100
« Reply #7 on: November 19, 2012, 09:52:36 PM »
I'll chime in here....

I have a similar slot with the Progressive system.

When I first started working on mine, it would tilt
all the time. What I found out is.... I think these slots
won't do anything right until the progressive system
has values set into them.  If your battery was dead
or disconnected, you lost the programming for the
Progressive.

I can tell, because your slot shows blank and zero
on the upper mechanical displays.  They have to display
something other that what you have.

Someone passed this on to me and it helped me get going;

http://home.mchsi.com/~litterbox99/temp/Bally%20E2000%20Progressive%20Programing.rtf

It's a bit tricky, but eventually you'll get it.

Once I did this, I was able to proceed further in my diagnosis.


Hope this helps !

Todd

 

 
Logged
tkrozleski
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 23
Offline Offline

Gender: Male
Posts: 308
« Reply #8 on: November 19, 2012, 09:55:45 PM »
Also take a look at those 18 total  (3 columns 6 per column) of redish brown ceramic capacitors on the I/O board on the upper right corner labelede C1- etc. Look to see if any of those are deteriorating and the ceramic is splitting or cracking. If so that can cause problems. Swap with a known working I/O board.
Logged
tkrozleski
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 23
Offline Offline

Gender: Male
Posts: 308
« Reply #9 on: November 19, 2012, 10:12:05 PM »
Litterbox, Thank You! My next project is a progressive and most likely this info will be very helpful!

Thanks!

Tim
Logged
drfreeze1739
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 16
Offline Offline

Gender: Male
Posts: 432


drfreeze1739@sbcglobal.net
« Reply #10 on: November 19, 2012, 10:52:54 PM »
Quote from: litterbox99 on November 19, 2012, 09:52:36 PM
I'll chime in here....

I have a similar slot with the Progressive system.

When I first started working on mine, it would tilt
all the time. What I found out is.... I think these slots
won't do anything right until the progressive system
has values set into them.  If your battery was dead
or disconnected, you lost the programming for the
Progressive.

I can tell, because your slot shows blank and zero
on the upper mechanical displays.  They have to display
something other that what you have.

Someone passed this on to me and it helped me get going;

http://home.mchsi.com/~litterbox99/temp/Bally%20E2000%20Progressive%20Programing.rtf

It's a bit tricky, but eventually you'll get it.

Once I did this, I was able to proceed further in my diagnosis.


Hope this helps !

Todd

 

  When turnd on i get numbers on the porgresve on top...
When i push the test and reset buttons on the hooper they go away and then come back...

All the red compasitors look good..
Logged
Mark
drfreeze1739
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 16
Offline Offline

Gender: Male
Posts: 432


drfreeze1739@sbcglobal.net
« Reply #11 on: November 19, 2012, 10:56:03 PM »
When turnd on i get numbers on the porgresve on top...
When i push the test and reset buttons on the hooper they go away and then come back...

All the red compasitors look good..
Logged
Mark
drfreeze1739
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 16
Offline Offline

Gender: Male
Posts: 432


drfreeze1739@sbcglobal.net
« Reply #12 on: November 19, 2012, 10:59:42 PM »
pics

* 100_4710.JPG (539.15 KB, 2048x1536 - viewed 256 times.)

* 100_4708.JPG (512.06 KB, 2048x1536 - viewed 303 times.)
Logged
Mark
drfreeze1739
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 16
Offline Offline

Gender: Male
Posts: 432


drfreeze1739@sbcglobal.net
« Reply #13 on: November 19, 2012, 11:47:41 PM »
When i first open door and turn it on it shows 80.03.0.0.1

Then when i shut the door you can here it all try to activate the door and stuff then it deactivtes and shows tilt and 50.000 in the cld and nothing works now since the door is closed.. and the progesive went blank.with nothing showing..

but if i open the door and do a reset the progesave comes back and shows numbers...

then when i lock the dooe it shows 50.80.00 and still in tillt and nothing still works..
Logged
Mark
tkrozleski
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 23
Offline Offline

Gender: Male
Posts: 308
« Reply #14 on: November 20, 2012, 12:39:57 AM »
What are your voltages at the test points on the power supply, the MPU, and the I/O ?
Logged
drfreeze1739
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 16
Offline Offline

Gender: Male
Posts: 432


drfreeze1739@sbcglobal.net
« Reply #15 on: November 20, 2012, 02:38:29 AM »
Dose anyone have the PSU voltage??

I had a page that showed me and now i cant find it
Logged
Mark
Amachanic
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 308
Offline Offline

Gender: Male
Posts: 1392
« Reply #16 on: November 20, 2012, 02:55:08 AM »
Quote from: drfreeze1739 on November 20, 2012, 02:38:29 AM
Dose anyone have the PSU voltage??

I had a page that showed me and now i cant find it

Power supply's voltages are, 5V, 7.5V, and 10V
Logged
If it's jammed, force it... If it breaks it needed to be replaced anyway...
tkrozleski
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 23
Offline Offline

Gender: Male
Posts: 308
« Reply #17 on: November 20, 2012, 10:30:32 PM »
TP = Test Point

PowerSupply board test point info-
TP 1 (+5 ) to TP 3 (GND) should be apprx 5 volts DC
TP 2 (ZC) to TP 3 = 7.5 volts DC
TP 4 (+UR) to TP 3 = 10 volts DC

I/O BOARD -  in the upper left corner
TP (neg) - to TP (pos) + = 5 volts DC

MPU-
I do not see test points on the spare E2000 board I have or shown in the manual either.
Logged
drfreeze1739
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 16
Offline Offline

Gender: Male
Posts: 432


drfreeze1739@sbcglobal.net
« Reply #18 on: November 20, 2012, 10:50:39 PM »
update...

Been messing with the power supply connector and the power connector on the MPU and now i get

no numbers in the top progeseve and i got it to energize the door and everything and the tilt light is out....

it says insert coin..... but when i put a coin in it will tilt right away and have to press restart button on hopper and then it goes right back to working mode except no numbers up top and put a coin in and it will tilt again..
Logged
Mark
tkrozleski
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 23
Offline Offline

Gender: Male
Posts: 308
« Reply #19 on: November 20, 2012, 11:14:43 PM »
Your best bet is to take all the boards out and get a stainless steel bristle brush the size of a tootbrush from the hardware and shine up all the pins which the harnesses connect to. I would bet the tin coating on all the pins have a dull oxidized coating creating all your problems.
Logged
Amachanic
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 308
Offline Offline

Gender: Male
Posts: 1392
« Reply #20 on: November 21, 2012, 12:09:32 AM »
I would pull the power supply and check the solder joints on the pins for the plug. I have found and repaired many cracked and broken connections. I have found the same problem on the MPU plugs before, but not as severe as the one on the power supply's.

Gary
Logged
If it's jammed, force it... If it breaks it needed to be replaced anyway...
drfreeze1739
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 16
Offline Offline

Gender: Male
Posts: 432


drfreeze1739@sbcglobal.net
« Reply #21 on: November 21, 2012, 01:21:42 AM »
Here are some pics of the back of the MPU board
Logged
Mark
drfreeze1739
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 16
Offline Offline

Gender: Male
Posts: 432


drfreeze1739@sbcglobal.net
« Reply #22 on: November 21, 2012, 01:23:08 AM »
MPU board

* 100_4705.JPG (473.28 KB, 2048x1536 - viewed 294 times.)

* 100_4713.JPG (481.98 KB, 2048x1536 - viewed 272 times.)
Logged
Mark
drfreeze1739
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 16
Offline Offline

Gender: Male
Posts: 432


drfreeze1739@sbcglobal.net
« Reply #23 on: November 21, 2012, 01:24:19 AM »
PSU BOARD

* 100_4714.JPG (530.95 KB, 2048x1536 - viewed 300 times.)

* 100_4715.JPG (464.78 KB, 2048x1536 - viewed 288 times.)
Logged
Mark
drfreeze1739
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 16
Offline Offline

Gender: Male
Posts: 432


drfreeze1739@sbcglobal.net
« Reply #24 on: November 21, 2012, 02:40:08 AM »
Dose any one know what these 2 buttons are for???

They are located behind the top glass in the wood housing....

* 100_4716.JPG (476.59 KB, 2048x1536 - viewed 270 times.)

* 100_4717.JPG (478.84 KB, 2048x1536 - viewed 288 times.)
Logged
Mark
Pages: [1] 2 Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.094 seconds with 20 queries.