Welcome, Guest. Please login or register.
November 22, 2024, 01:35:01 AM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  Bally Reel Games. (Moderator: a69mopar)
| | |-+  bally s5500 ram clear chip problem		 0 Members and 2 Guests are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: bally s5500 ram clear chip problem  (Read 11042 times)
trashman
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 49
« on: December 30, 2013, 10:15:07 PM »
hi i had a 54 and 71 code i couldnt clear so i ordered a set of safe clear ram chips.i did a partial got rid of the 71 code but not the 54 so i did a complete no help there either so then i did a full and then i had nothing no lights no display.so i went back and did a complete now i have a 83f code and all the lights are flashing i dont no where to go from here any help would be appreciated thanks
Logged
proten
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 210
Offline Offline

Gender: Male
Posts: 1130
« Reply #1 on: December 31, 2013, 02:47:31 AM »
83f is most likely a dead battery.
Check it with a meter.
Logged
One step at a time.
paul
paul
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 20
Offline Offline

Gender: Male
Posts: 548
« Reply #2 on: December 31, 2013, 11:39:35 PM »
54 is a side door open check inside switch and side door switch check all doors
Logged
trashman
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 49
« Reply #3 on: January 01, 2014, 08:53:44 AM »
ok i ordered the battery and i will check the switchs thanks everyone i let know when the out come.THANKS
Logged
paul
paul
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 20
Offline Offline

Gender: Male
Posts: 548
« Reply #4 on: January 02, 2014, 01:28:46 AM »
what is the voltage of your battery if it is below 3v get new if above close all doors and 54 should go away
Logged
trashman
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 49
« Reply #5 on: January 06, 2014, 08:59:55 PM »
ok so i put in a new battery in  then i got the low battery code so i did a full saferam clear still getting the 83f error with all the lights flashing.any other ideas thanks
Logged
proten
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 210
Offline Offline

Gender: Male
Posts: 1130
« Reply #6 on: January 06, 2014, 09:34:17 PM »
Try checking the new battery while it's still
on the board.  There have been bad new
battery's that are low when installed.
Logged
One step at a time.
trashman
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 49
« Reply #7 on: January 06, 2014, 09:45:08 PM »
im getting 3.6 volts
Logged
proten
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 210
Offline Offline

Gender: Male
Posts: 1130
« Reply #8 on: January 06, 2014, 10:06:47 PM »
Trace the circuit and see if the voltage is getting where it needs to go.
You may have a bad trace do to leaking battery.
Logged
One step at a time.
trashman
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 49
« Reply #9 on: January 07, 2014, 07:04:38 AM »
i did and i do
Logged
Jim
MIDWEST SLOTS
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 288
Offline Offline

Gender: Male
Posts: 1172


513-984-2201
« Reply #10 on: January 14, 2014, 12:35:59 PM »
is the jumper in the right position?  there is a set of jumpers next to the battery, you could disconnect the battery from the circuit if you didn't want to run it down during long periods of non use. Maybe its in the wrong position? 

Some thing in and around that area is your problem, the rest of the board seems to be doing what it should be, if you get this resolved, then the machine should work.


Jim
Logged
MIDWEST SLOTS   Selling Quality Slot Machines since 1995.  We service and repair all types of slot machines. Mills, Jennings, Bally EM, 1000/2000 series, Proslot, 6000. IGT  M, M+ ,S,  S+, S-2000,  I-Game,  Universal,  Video Poker, Sigma.
trashman
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 49
« Reply #11 on: January 14, 2014, 04:01:22 PM »
i dont know any thing about jumpers i did soldier the one wire to the battery it had like a rechargeable battery pack on the board will hers a pic maybe you see some thing.thanks

* 005.JPG (1488.49 KB, 2048x1536 - viewed 589 times.)
Logged
proten
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 210
Offline Offline

Gender: Male
Posts: 1130
« Reply #12 on: January 14, 2014, 04:09:49 PM »
The two pins of the jumper(JW1) are spouse to be connected together ( the two pins in the red plastic).
The way you have it the voltage can't get past the jumper.
Logged
One step at a time.
trashman
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 49
« Reply #13 on: January 15, 2014, 08:59:21 PM »
i did that no help still have 83 f code
Logged
proten
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 210
Offline Offline

Gender: Male
Posts: 1130
« Reply #14 on: January 15, 2014, 10:31:08 PM »
Ok I made a mistake. JW 1 is not the right jumper.
The pin that you have the wire from the battery connected
 to and the pin next to it (JW12or14)are spouse to be connected.

Logged
One step at a time.
trashman
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 49
« Reply #15 on: January 16, 2014, 04:59:31 PM »
i did that didnt change any thing.i  even did a reset again still got the 83f
Logged
proten
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 210
Offline Offline

Gender: Male
Posts: 1130
« Reply #16 on: January 16, 2014, 06:19:59 PM »
You must have another problem with that board.
I see what looks like corrosion at the U54 chip.
You could have acid damage under the socket.
Logged
One step at a time.
trashman
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 49
« Reply #17 on: January 16, 2014, 07:37:58 PM »
DO you fix these board i dont see any rott on the board or have a board for sale i will look on e-bay to if so can you give me a ruff estimate as to what it will cost board or repair mine. thanks
Logged
proten
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 210
Offline Offline

Gender: Male
Posts: 1130
« Reply #18 on: January 16, 2014, 07:51:16 PM »
I'm not a "repair" person as I just tinker with this stuff.
If I was you I would post a WTB (want to buy) and get another board
then if wanted I could look at it and see if I can find out why it is giving that code.
 
Logged
One step at a time.
paul
paul
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 20
Offline Offline

Gender: Male
Posts: 548
« Reply #19 on: January 17, 2014, 01:45:30 AM »
Raz410 might be able to help   with problem
Logged
proten
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 210
Offline Offline

Gender: Male
Posts: 1130
« Reply #20 on: January 17, 2014, 01:58:36 AM »
Here is a board at Rudy's reaty to go.

http://rudysdeals.com/index.php?route=product/product&path=88&product_id=1189
Logged
One step at a time.
trashman
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 49
« Reply #21 on: January 17, 2014, 06:48:37 AM »
i saw that i would just have to switch the eproms and jumpers right.          p.s  i pm Raz410  thanks everyone
Logged
proten
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 210
Offline Offline

Gender: Male
Posts: 1130
« Reply #22 on: January 17, 2014, 10:21:07 AM »
yes but that's not a big deal
Logged
One step at a time.
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.112 seconds with 19 queries.