Welcome, Guest. Please login or register.
November 24, 2024, 11:21:46 AM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  IGT S and S-plus Reel Games. (Moderator: knagl)
| | |-+  blowing fuses		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: blowing fuses  (Read 7867 times)
Slam
NLG Member 101 to 500 Post
***

Total Karma Storms: 12
Offline Offline

Gender: Male
Posts: 103
« on: January 27, 2014, 10:34:45 PM »
Hi all, This one has me stumped. s-plus  I have read other posts on this & could not find a solution. When I plug in the molex for the hopper, the top 6a fuse blows & the display goes out. I checked power supply for coins, looked ok, swapped it with a known working one. checked the solenoid wires for the pull arm, not shorting on the case. installed a known working mpu & mother board, installed a known working complete door & harness. clipped ties on harness for the hopper wires, traced wires, no shorts found. installed a known working receptor for the hopper. Still blowing the darn fuse. Any other suggestions other than a big hammer?   hissy fit  hissy fit  hissy fit  hissy fit  hissy fit
Logged
CVslots
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 432
Offline Offline

Gender: Male
Posts: 2803



WWW
« Reply #1 on: January 28, 2014, 02:26:12 AM »
This is a case for Jim/MidWest or stayoutofthebunker.....
Logged

www.CentralValleySlots.com
Email: centralvalleyslots@yahoo.com
Jim
MIDWEST SLOTS
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 288
Offline Offline

Gender: Male
Posts: 1172


513-984-2201
« Reply #2 on: January 28, 2014, 03:06:38 AM »
P/J109   from the power supply carry 115vac from the power supply to the SSR ( SOLID STATE RELAY)  hot side,  and the common goes to the hopper plug.  either something is miss wired  in or around the SSR.  If the machine works with this plug undone  then the problem has to be with the SSR or the wiring to it.  the SSR has 5 wires going to it,  gray/red to pos.#2, gray/violet to pos.#1, and green to the center position. on the other side two posts, black/red to one post, comes from the plug j109, white/black from the other post goes to pin 11 of the hopper plug.  pin three from the plug  J109 go to the hopper plug pin 12, its color is white/red.  pin2  J109 is the earth ground  green/yellow.


Hope this helps

Jim   
Logged
MIDWEST SLOTS   Selling Quality Slot Machines since 1995.  We service and repair all types of slot machines. Mills, Jennings, Bally EM, 1000/2000 series, Proslot, 6000. IGT  M, M+ ,S,  S+, S-2000,  I-Game,  Universal,  Video Poker, Sigma.
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #3 on: January 28, 2014, 03:58:03 PM »
I totally agree with Jim.^^^   yes
I'm pretty sure somebody swapped a wire connector either on the SSR or the hopper beau plug.
Here's a couple of pics.
Click on the photos if you want to enlarge to see the wiring color stripes and where they're going to.
The top one is the SSR and the bottom one is from behind the hopper plug/motor connector area...>>>

* hopper plug 002.JPG (937.59 KB, 2576x1932 - viewed 920 times.)

* hopper plug 007.JPG (755.87 KB, 2576x1932 - viewed 674 times.)
« Last Edit: January 28, 2014, 04:10:07 PM by stayouttadabunker » Logged
Jim
MIDWEST SLOTS
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 288
Offline Offline

Gender: Male
Posts: 1172


513-984-2201
« Reply #4 on: February 03, 2014, 03:34:28 PM »
Did you ever figure this out?????
Logged
MIDWEST SLOTS   Selling Quality Slot Machines since 1995.  We service and repair all types of slot machines. Mills, Jennings, Bally EM, 1000/2000 series, Proslot, 6000. IGT  M, M+ ,S,  S+, S-2000,  I-Game,  Universal,  Video Poker, Sigma.
Slam
NLG Member 101 to 500 Post
***

Total Karma Storms: 12
Offline Offline

Gender: Male
Posts: 103
« Reply #5 on: February 03, 2014, 06:53:08 PM »
Quote from: Jim on February 03, 2014, 03:34:28 PM
Did you ever figure this out?????
No luck, I decided to just yank the coin stuff & set it up for hand pay.
Logged
Jim
MIDWEST SLOTS
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 288
Offline Offline

Gender: Male
Posts: 1172


513-984-2201
« Reply #6 on: February 03, 2014, 07:01:20 PM »
that makes no sense at all.    So the entire machine works, EXCEPT  when that top molex plug is plugged in???   then it blows a fuse??      that cable only handles 115vac.   

I would love to see that coin stuff, I love a good challenge, I've NEVER had a S+ that I couldn't fix.


Jim
Logged
MIDWEST SLOTS   Selling Quality Slot Machines since 1995.  We service and repair all types of slot machines. Mills, Jennings, Bally EM, 1000/2000 series, Proslot, 6000. IGT  M, M+ ,S,  S+, S-2000,  I-Game,  Universal,  Video Poker, Sigma.
Slam
NLG Member 101 to 500 Post
***

Total Karma Storms: 12
Offline Offline

Gender: Male
Posts: 103
« Reply #7 on: February 03, 2014, 07:03:25 PM »
Quote from: Jim on February 03, 2014, 07:01:20 PM
that makes no sense at all.    So the entire machine works, EXCEPT  when that top molex plug is plugged in???   then it blows a fuse??      that cable only handles 115vac.    

I would love to see that coin stuff, I love a good challenge, I've NEVER had a S+ that I couldn't fix.


Jim
I would send you some pics, but I put the parts back into the Earthquake machine, It all works fine in that one. I'll probably mess with it more in the future, but for now its good enough. I have several other machines that need attention at the moment that I want to get out of the way. When I do find the problem, I'll be sure to post it.
« Last Edit: February 03, 2014, 07:09:16 PM by Slam » Logged
mvco
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 41
Offline Offline

Gender: Male
Posts: 412
« Reply #8 on: February 03, 2014, 10:55:23 PM »
I had this same exact thing happen about 6 months ago.  Had a guy bring a machine for repair (S-Plus)  It would blow that 6 amp fuse unless the molex to the hopper was disconnected.
Now here is where it gets strange.  It ended up being a wire touching the cabinet wall at the handle release solenoid.   WTF?  I kept looking at the schematic, thinking this makes no dam sense whatsoever.  But hell, why argue, the machine is now fixed and not blowing the fuse.  My mind will never put this one together, the strangest thing I have had happen on any slot.  A WTF for life, LOL's
Logged
Slam
NLG Member 101 to 500 Post
***

Total Karma Storms: 12
Offline Offline

Gender: Male
Posts: 103
« Reply #9 on: February 03, 2014, 11:31:01 PM »
Quote from: mvco on February 03, 2014, 10:55:23 PM
I had this same exact thing happen about 6 months ago.  Had a guy bring a machine for repair (S-Plus)  It would blow that 6 amp fuse unless the molex to the hopper was disconnected.
Now here is where it gets strange.  It ended up being a wire touching the cabinet wall at the handle release solenoid.   WTF?  I kept looking at the schematic, thinking this makes no dam sense whatsoever.  But hell, why argue, the machine is now fixed and not blowing the fuse.  My mind will never put this one together, the strangest thing I have had happen on any slot.  A WTF for life, LOL's
That's the second thing I checked, looked good.
Logged
jay
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 483
Offline Offline

Gender: Male
Posts: 3178


if you cant afford to lose you cant afford to win
« Reply #10 on: February 04, 2014, 05:40:14 AM »
Could be a bad hopper motor.....

A motor is a big coil of insulated wire... doesn't take much for a wire to get overheated in a 20 (plus+) year old hopper......and once the insulation burns off.... you get a short.

Do you have a different hopper you can try ??
Logged
The only way to beat the casino is to own it
Slam
NLG Member 101 to 500 Post
***

Total Karma Storms: 12
Offline Offline

Gender: Male
Posts: 103
« Reply #11 on: February 04, 2014, 11:36:40 AM »
Quote from: jay on February 04, 2014, 05:40:14 AM
Could be a bad hopper motor.....

A motor is a big coil of insulated wire... doesn't take much for a wire to get overheated in a 20 (plus+) year old hopper......and once the insulation burns off.... you get a short.

Do you have a different hopper you can try ??
It blows the fuse without the hopper installed.
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #12 on: February 04, 2014, 01:52:50 PM »
I wonder if the SSR might have a short inside when warmed up?
It's that red (sometimes black) plastic box next to the hopper beau plug.
I never took one apart...I don't know what's inside of it really.
Logged
jay
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 483
Offline Offline

Gender: Male
Posts: 3178


if you cant afford to lose you cant afford to win
« Reply #13 on: February 04, 2014, 03:18:46 PM »
I always suspect coins under the motherboard.
Logged
The only way to beat the casino is to own it
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #14 on: February 04, 2014, 03:23:22 PM »
Quote from: jay on February 04, 2014, 03:18:46 PM
I always suspect coins under the motherboard.

Me too but that's more and more rare ever since they put that gray foam piece under there?
But yeah, not all machines have it.
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.097 seconds with 20 queries.