What model is my Universal ????????

[Randy0777]

Hi Uniman,I read your other post about this topic and did not think I should hi-jack the thread  .
I tried pressing the buttons to move through the menu,but no luck 
The tilt light is flashing on the reel glass, and the crdit meter says 3300 and the win meter says(well the last four numbers are staying at 5550) but the first two rotate between 55,50,and 14 
Thanks for any help 

[uniman]

Feel free to hijack any of the Universal threads. They don't get much replys anyways! 

Your machine, Phantom Spin, has the 8800 board. The 5555 is not normal! Error 50 is door open, error 14 is excessive credits.
Since your credit meter says 3300 and Universal only allowed up to 2500 credits, I would say that's your problem.
Easiest thing to do is a simple RAM clear.
1.Shut the machine off.
2. In the round hole at the top of your board there should be a tiny push button. Push and hold this button in while powering up the machine. Hold it in for about three seconds and release. (Push and hold, then power up, continue to hold for 3 sec's)
3. Hopefully all should be good now!  

Cool game! A lot like IGT Haywire, this game respins. But if you hit the three Phantoms, the game will respin to three 7's, then to Triple Bars, then Double Bars, and finally Bars! So you get the jackpot and 540 credits more! Very cool!!!  

Game Chip # 9355
Machine Chip # 9116.043
Sound Chip 8953.044

[Randy0777]

Thanks for the reply 
Held the button in and did a reset..... Now win meter stays at all 0's and the credit meter is staying at 1110 

[uniman]

Very Strange!
You probably already did, but do another clear.

[Randy0777]

I installed the hopper and done another clear,now I get  1110 as the last four of the win and the first two rotate between 10 and 11 and credit says 1110. Also,the does not have a bill validator in it

[uniman]

Sounds like board trouble. 
Almost like your in Test Mode. I would check the wiring behind (or left) of the board for any coins, tokens, screws, etc that maybe shorting the system. But it really looks like board trouble.
Give me a bit of time to dig up the dip switch settings for the 8800 board. With no BV, you need to have dips set to no BV.

Jim

[uniman]

There is a 4-dip switch at the front of the board. (SW#2 )With no BV, turn all four off.
I'm sure this is not your problem with the meters, but that is the setting.

[Randy0777]

The one on the left or the middle ? ...the one on the left has the four of them off

Just seen wher you said 2  ...putting it together

[Randy0777]

On the win meter I get ,94,50,13...all the rest is zero.


EDIT,after another reset I get 94 and 50

[uniman]

Any error in the 90's is a BV error. 13 is power interrupt, not a problem at powerup. 50 is door open, it continue to blink until game is initiated. Same with 13.
Errors in the 90's will cause a tilt. Not 13 or 50.
(Need to do a RAM clear whenever dip switches are changed.)



The Red Wings win again! 

[uniman]

Almost forgot, error 94 is BV has no power. If all switches are OFF on SW2 this error should not happen.

[Randy0777]

On the two switches that have four,all of them are off  I do not know what the larger dip switch settings do. And I can not get rid of the 50 code. Held themin,pulled them out (when I do one of them it plays a sound)

Just pulled the board and checked them again.... one was not pushed ALL the way 

Anyway,the game is playing      JIM 

[tacman]

Very nice to hear, good job Jim. That theme looks very interesting. What type of audio does it play?

 Dan (tacman)

[Randy0777]

I'll be able to tell you soon  Cleaning the reels,etc.

It plays some beeping sound when the reels spin,if you get a phantom is plays something weird and the reels spin faster and longer. If you win ,a bell goes off(like a jackpot bell). I had one phantom and a 7 and it played something else and started a re-spin.....as far as I got

And what type of BV do these things take

[uniman]

The sound is a bit strange for this game. An erie spin sound.

The dip switches;

SW1   an 8-pac dip    #1 thru #4 are used for credit limit. All four ON is maximum credit limit of 2500.
                              #5 is for the candle. OFF if you want it to flash, ON if you want it on.
                              #6-#7 for hopper type, OFF-OFF regular hopper, OFF-ON asahi-seiko hopper, ON-OFF and ON-ON for high speed hopper.
                              #8 for credit/cash    ON for credit only, OFF for credit selectable (must push cashout button before play for credit)

SW2      an 4-pac dip   #1  ON for 5 cent game
                               #2  ON for 10 cent game   
                               #3  ON for 50 cent game
                               #1-2-3 OFF for BV inactivated
                               #1-2 ON for 25 cent game
                               #1-3 ON for dollar game
                               #2-3 ON for five dollar game
                               #1-2-3 ON for ten dollar game
                               #4 ON for JCM BV  and OFF for MARS BV

SW3     an 4-pac dip   #1 ON for first progessive signal out/ OFF no signal
                              #2 ON for second progessive singal out/ OFF no signal
                              #3 ON for third progressive signal out/ OFF no signal
                              #4 ON Progressive full lockup/ OFF Progressive partial pay to lockup

Hope that helps!
Jim

[uniman]

They take a JCM or MARS BV. Even a CVB model IVO. Ever hear of that one?
I have never worked on a BV for the 8800.

When you get a combination of Phantom and/or 7's in the first two reels you get "The Third Reel Reach Feature."
The third reel spins longer and extra sound is added as a teaser.

The respin goes "Tink", then whirl, whril, whril.  That's how I describe it.
Not as good as IGT Haywire. IMO

[Randy0777]

CVB model IVO. Ever hear of that one? <<<<Nope I was just looking where the plug is and just seemed strange . Oh well,guess I need to find one 

[uniman]

I really didn't like the way Universal reduced the belly glass size to put the BV in so I never bought one of those.
I have a manual on the MARS and CVB (Coin Bill Validator of Deer Park New York), but I have no manual on the 8800, just the dip settings.
Too bad too, because I see a plug for backlit reels on this board. Must have been for the Mustang Game?

[Randy0777]

Hi Jim, when I replied to you last night about the % chip....pushing the button nine times,anyway. When I played it later I lost all reel sound except the "bell" when you win. Was thinking about an IGT under the menus and figured I must of changed something  .  So I did a clear today and the sound was back  . I let it sit with credits on it for a few hours and just tried to play it,no sound except for the bell. I did a clear again and the reel sound is back

[uniman]

Right before I moved out here to Nevada I fixed a Phantom Spin for a friend. It would lose sound right after a respin. Problem was wrong sound chip. I suspect that could be your problem.

The machine chip requests a particular sound for each event, i.e. coin in, win meter, and respin. If it requests a respin sound and your sound chip doesn't have it, the sound processor gets lost. Result is total lose of sound from that point on!

Check your sound chip. You will need to remove the daughter board as the sound chip is under it. Your sound chip should be labeled 8953-0044. All universal sound chips begin with 8953, the 0044 is the important part.

When the reels spin would you describe the sound as erie? When it respins, you should here a sound like Tink, then whirl, whirl, whirl.

[Randy0777]

When the reels spin would you describe the sound as erie? When it respins, you should here a sound like Tink, then whirl, whirl, whirl.   <<<< Um  Give me a few,I was just playing it and it did three re-spins and then I noticed no sound again. Let me answer the sound question than I'll pull the board

[Randy0777]

It sounds "normal" to me until i hit the re-spin ....which is when all sound is lost.
Check your PM

[Randy0777]

Getting ready to try the sound and game chip (  uniman ) . Oh,and get ready for some questions on the BV 

Edit: Well,neither of them went well . The sound chip made a loud hum when turned on and the BV keeps giving a code of 94 (power off) I tried the DIP for Mars and JCM  .

[tacman]

WOW, Jim. Is it me or has there been many Universal questions from owners recently? Must be nice to know you are now no longer alone! The Uniman army grows!! 

 Dan (tacman)

[Randy0777]

Hi Dan, I was checking out different sections about a week ago and was wondering WTH is the Universal section. Come to find out it was the brand of machine  . I was reading through it and like two days later I ran across some of them. So I grabbed one ...neither of us knew what was wrong with it. But if I never seen this section that machine would still be sitting next to the other three Universals  I was there yesterday and was able to get one of them working (Thanks Jim) . Ran out of time on the other two .