Welcome, Guest. Please login or register.
October 31, 2024, 09:54:00 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  Bill Validators and Currency acceptors
| |-+  JCM DBV-45, DBV-145, and DBV-200 Bill Validators.
| | |-+  Change BV conenctor ?
0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Change BV conenctor ?  (Read 13149 times)
nilgaming
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 3
Offline Offline

Gender: Male
Posts: 98



WWW
« on: September 16, 2009, 04:15:14 PM »

Hi all,

I recently bought a machine with a BV.
When i received it the BV was inside, looking good, but not really meant to be there.
In fact the connector inside the machine is not the same connector as the BV connector.
Obviously they d not match.
Question 1 :
What kind of BV is that ? brand ? Model ? i think it's a JCM but i am new to BV so i might be wrong.
Question 2 :
How can i make these 2 match ?
Can I change the BV connector to fit in the other one ?

see pictures below...

Thanks !


* machine connector.JPG (378.75 KB, 1944x2592 - viewed 310 times.)

* BV Connector.JPG (441.02 KB, 1944x2592 - viewed 339 times.)
Logged

nilgaming
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 3
Offline Offline

Gender: Male
Posts: 98



WWW
« Reply #1 on: September 16, 2009, 04:16:07 PM »

here are the stickers on the BV...


* on top of the BV.JPG (453.21 KB, 2592x1944 - viewed 314 times.)

* On the front of the BV.JPG (349.84 KB, 2592x1944 - viewed 311 times.)
Logged

nilgaming
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 3
Offline Offline

Gender: Male
Posts: 98



WWW
« Reply #2 on: September 16, 2009, 04:18:00 PM »

and finally some pictures of the BV itself.
by the way it's a EURO BV.

All is fine inside the machine (stacker, ...) except the connector.
is it hopeless or do i have a chance to get ths baby to work one day  Scratch Head

thanks a lot !

Jay (the other one)



* face A.JPG (472.71 KB, 2592x1944 - viewed 356 times.)

* Face B.JPG (501.92 KB, 2592x1944 - viewed 337 times.)
Logged

Op-Bell
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 326
Offline Offline

Gender: Male
Posts: 854



« Reply #3 on: September 17, 2009, 05:13:21 AM »

What you have there is a WBA22/23 frame, which is what the machine was equipped with, but an obsolete WBA20 transport.  Maybe the seller did a nasty switch on you. It is possible to upgrade the 10/11/20/21 to the 12/13/22/23 - we've been discussing the availability of upgrade kits here recently - or you may be better off to get a used 12/13/22/23. The WBA12 is US Flash, the 13 is US EPROM. The 22 is Euro flash, the 23 is Euro EPROM. Change a 12/13 into a 22/23 just by swapping the head, and of course updating the software.
Logged
nilgaming
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 3
Offline Offline

Gender: Male
Posts: 98



WWW
« Reply #4 on: September 17, 2009, 05:23:07 AM »

Hi,

thanks a lot for the explaination.
Seems very complicated to me...  Scratch Head

I have no clue where to find ... i don't even know what i am looking for !
A "WBA22/23 transport" ? is that what i should look for ?
Then i swap the head (what's the head ? and with what  Scratch Head)
And i update the software...  bawling

I'm lost. I guess i can just throw that thing away and forget it...  bawling


thanks op-bell

Jay (the other one)
« Last Edit: September 17, 2009, 01:56:00 PM by idesign » Logged

Op-Bell
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 326
Offline Offline

Gender: Male
Posts: 854



« Reply #5 on: September 17, 2009, 05:33:13 AM »

The head is the bit the note enters that contains all the sensors. There's a bar across the front of the BV, if you push it down you can slide the head out forward. It's a block about 80mm square and 30mm deep. All WBAs use the same head so at least keep that bit. Don't despair, there are millions of WBAs around on the used market and all the help you need here to get up and running. What is the game - what manufacturer?
Logged
nilgaming
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 3
Offline Offline

Gender: Male
Posts: 98



WWW
« Reply #6 on: September 17, 2009, 06:02:44 AM »

thanks for the support.
machine is from Holland, from ORION, machine name is WHEEL OF ADVENTURE.
i have opened a few topics because i have a number of problems with it.

this one with a CC problem :
http://newlifegames.net/nlg/index.php?topic=4467.0

this one where you can see pictures of it :
http://newlifegames.net/nlg/index.php?topic=4372.0

thanks !

Jay
Logged

a69mopar
647-402-1977
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 600
Offline Offline

Gender: Male
Posts: 3508



WWW
« Reply #7 on: September 17, 2009, 01:28:56 PM »

you only need the transport, the head is the same. You could use either a WBA 13/23 eprom version (13 and 23 transport are interchangeable), you would need the software of course.  You can use the Flash versions, but you need to be able to flash them with the software.  You could also convert the current transport, but I doubt it would be any cheaper and the software would still be required.

Thanks,
Wayne


* WBA11 21 AND 13 23 DIFFERENCES.jpg (448.11 KB, 1786x1037 - viewed 452 times.)
Logged

         www.GTASLOTS.com      647-402-1977              BALLY S6000 GALLERY
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447



« Reply #8 on: September 17, 2009, 01:37:06 PM »

Hi,

thanks a lot for the explaination.
Seems very complicated to me...  Scratch Head

I have no clue where to find ... i don't even know what i am looking for !
A "WBA22/23 transport" ? is that what i should look for ?
Then i swap the head (what's the head ? and with what  Scratch Head)
And i update the software...  bawling

I'm lost. I guess i can just throw that thing away and forget it...  bawling

thanks op-bell

Jay (the other one)




Whew!
Harsh words for that seller! LOL
Hear some sililarities here? Tongue Out

<a href="http://www.youtube.com/v/tBeeghdLsJc&rel=0" target="_blank">http://www.youtube.com/v/tBeeghdLsJc&rel=0</a>
« Last Edit: September 17, 2009, 01:56:49 PM by idesign » Logged
a69mopar
647-402-1977
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 600
Offline Offline

Gender: Male
Posts: 3508



WWW
« Reply #9 on: September 17, 2009, 01:39:50 PM »

It would be easier to change the machine harness to match the Bill Acceptor.  The housing would be the same.

Thanks,
Wayne
Logged

         www.GTASLOTS.com      647-402-1977              BALLY S6000 GALLERY
a69mopar
647-402-1977
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 600
Offline Offline

Gender: Male
Posts: 3508



WWW
« Reply #10 on: September 17, 2009, 01:51:36 PM »

here are pics of heads, it pulls out of the transport by pressing down on the bar below it and pulling the head out.  The pics were to show the difference between wba 1x and wba2x heads.

W


* DIFFERENCE BETWEEN WBA21 AND 11sm.jpg (167.69 KB, 1000x684 - viewed 456 times.)
Logged

         www.GTASLOTS.com      647-402-1977              BALLY S6000 GALLERY
Op-Bell
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 326
Offline Offline

Gender: Male
Posts: 854



« Reply #11 on: September 17, 2009, 03:14:33 PM »

Quote
It would be easier to change the machine harness to match the Bill Acceptor.
That's assuming the WBA20 works. I wouldn't go to the trouble of changing the harness without knowing that first.
There hasn't been a Euro firmware update for the 20/21 since 2004, so I'm of the opinion that the seller pulled the real transport and shoved a bit of junk in its place.


Here's a contact for JCM in Belgium:

Seeben S.A.
Avenue du Parc 22
BE - 4650 Chaineux
Belgium
Tel: +32 87 315050 (Urbain Thewissen-Cntct.)
Fax: +32 87 313207 (Didier Chevigné-Tech.)
Email: seeben@jcm-germany.com

Or try the German office (actual JCM people not a third party)

Düsseldorf Sales & Service Office (Europe Headquarters)
Mündelheimer Weg 60
40472 Düsseldorf
Germany
Tel:+49 (0)211 - 530645-0
Fax:+49 (0)211 - 530645-65
Email: komanns@jcm-germany.com (Friedrich Komanns)


Logged
nilgaming
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 3
Offline Offline

Gender: Male
Posts: 98



WWW
« Reply #12 on: September 18, 2009, 05:01:50 AM »

Thanks to all of you for your help and pictures  Hail

i will try to find on the web, cheaper then through official resellers.

many thanks

Jay (the other one)
Logged

Pages: [1] Go Up Print 
« previous next »
Jump to:  


If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com    Newlifegames.net    Newlifegames.org
   New Life Games    NewLifeGames  NLG  We Bring new Life to old Games    1-888-NLG-SLOTS
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.111 seconds with 19 queries.