Welcome, Guest. Please login or register.
November 22, 2024, 12:39:48 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Video Slots** Gaming machines
| |-+  IGT PE and PE Plus Poker Games.
| | |-+  Question about bell for PE Slant Top 		0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Question about bell for PE Slant Top  (Read 11284 times)
Jimise
Don't pick it up by the candle!
Contributing NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 75
Offline Offline

Gender: Male
Posts: 752
« on: September 19, 2009, 09:04:28 PM »
Hello all, Does anyone have a Slant top PE+ Video Poker with a Jackpot bell in it?
The manual I have does not show any info about slant tops. If anyone could possibly
help me out as to where it hooks up to, Or plugs into? That would be much appreciated!
Thanks for all the help!   Jim........ Hail
Logged
jaeckleint
Guest
« Reply #1 on: September 19, 2009, 10:53:53 PM »
Guess you found you bell applause applause Can figure out where to plug mine in either (s+ round top) Scratch Head Scratch Head
Logged
Foster
The S2000 GURU
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 345
Offline Offline

Gender: Male
Posts: 2872
« Reply #2 on: September 19, 2009, 11:27:57 PM »
Connector for Bell on the motherboard is:

S+
Upright -- J11
Slant Top -- J14

PE+ -- J14

S2000/Vsiion -- Cabinet connector J135 Orange and Yellow/brown wires, most likely either hanging loose or wire tied to other wires near the cabinet I/O
« Last Edit: September 19, 2009, 11:44:19 PM by Foster » Logged
A Slot Machine and Coca-Cola Addict!!
"If it is not broke do not fix it" I keep forgetting that!
jaeckleint
Guest
« Reply #3 on: September 19, 2009, 11:54:42 PM »
Thank you very much  Hail applause
Logged
Jimise
Don't pick it up by the candle!
Contributing NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 75
Offline Offline

Gender: Male
Posts: 752
« Reply #4 on: September 20, 2009, 12:51:47 AM »
Cool, So the upright and the slant top are the same connector.

Well I stuck my head inside the machine and found J14 !

Thank you for the info Foster!!

Now I just need to find a plug that fits into J14  Tongue Out
Logged
Foster
The S2000 GURU
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 345
Offline Offline

Gender: Male
Posts: 2872
« Reply #5 on: September 20, 2009, 02:20:27 AM »
As long as J14 a 2 pin you should be fine.
Logged
A Slot Machine and Coca-Cola Addict!!
"If it is not broke do not fix it" I keep forgetting that!
Jimise
Don't pick it up by the candle!
Contributing NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 75
Offline Offline

Gender: Male
Posts: 752
« Reply #6 on: September 20, 2009, 02:57:54 AM »
Yes, J14 is a 2 pin on the board, But the plug on the bell is different. Scratch Head
 Looks like another wire goes in between the board and the bell.
 Thanks!!!   Jim..       
Quote from: Foster on September 20, 2009, 02:20:27 AM
As long as J14 a 2 pin you should be fine.
Logged
Foster
The S2000 GURU
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 345
Offline Offline

Gender: Male
Posts: 2872
« Reply #7 on: September 20, 2009, 05:38:27 AM »
IGT did the same on the S+.
Logged
A Slot Machine and Coca-Cola Addict!!
"If it is not broke do not fix it" I keep forgetting that!
jaeckleint
Guest
« Reply #8 on: September 20, 2009, 11:38:32 AM »
Looks like we need to make a jumper harness. I will check around radio shack and see if I can find the correct plugs to make the harness. Mine needs to be about  foot long , how about yours
Logged
Jimise
Don't pick it up by the candle!
Contributing NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 75
Offline Offline

Gender: Male
Posts: 752
« Reply #9 on: September 20, 2009, 02:27:10 PM »
That sounds like a good idea!!  A foot looks pretty close for mine, I think I would go for about 2 feet just for a bit more room to play with.Thanks for the info!!
Quote from: jaeckleint on September 20, 2009, 11:38:32 AM
Looks like we need to make a jumper harness. I will check around radio shack and see if I can find the correct plugs to make the harness. Mine needs to be about  foot long , how about yours
Logged
jaeckleint
Guest
« Reply #10 on: September 22, 2009, 11:44:04 PM »
Checked a couple of places and nobody local carrys the plug we need for the bell harness. Radio shack has one close but it is too big and they do not offer the smaller one. I have one more place to check but can"t get there till the weekend. After that...cut off the plug and improvise arrow arrow
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #11 on: September 23, 2009, 12:25:58 AM »
The 2 pins are actually soldered directly to the motherboard...
if you carefully remove the motherboard and place it on a benchtop,
under good lighting and magnification,
you can carefully lift the black plastic housing up cleanly off the pins
without pulling the pins out of the motherboard
and use female sockets instead going to the bell...

                     OR

You can pick them up at mouser.com
Click on the link below, open the sheet and look down on the left hand corner....
You'll see the 2-pin housing...
Type in the manufacturer number in the search box at mouser
and you'll see it pop up for .11 cents apiece.
On the right hand corner of the catalog page
you'll see the female crimp-style receptor pins that will fit your pins on the motherboard.
Remember, the 2-pin circuit is your "circuit size".
The EDP number is: 50-57-9402.

Type that number into the search box....
Here's some links to what you're looking for next time you want stuff! yes

http://www.mouser.com/ProductDetail/Molex/50-57-9402/?qs=u6Gr9%2fNt%252b%2f9jh%2fRowNBxRQ%3d%3d
* 2-pin receptacle housing.pdf (110.07 KB - downloaded 278 times.)
« Last Edit: September 23, 2009, 01:01:44 AM by stayouttadabunker » Logged
jaeckleint
Guest
« Reply #12 on: September 23, 2009, 12:47:12 AM »
Connection at motherboard not a problem...The connection to the bell harness that is at least a foot short is a 2 pin molex mini connector square one end and and pointed other end total of 3/8" wide that is the problem. We could just lop it off arrow but were trying to keep it neet and OEM looking. And if I want to sell the bell (or if my widowed wife does  frying pan frying pan frying pan) I would like it OEM condition without the connector cut off. no Have a big old electronics store not far from here I will try this weekend. They have everything and the price to match knockout But how much could a connector cost Scratch Head Scratch Head Scratch Head Without Happ's shipping applause
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #13 on: September 23, 2009, 01:04:49 AM »
Really, those are also at mouser too... Duh!

I give up...go look in radio shack and see what you'll find. frying pan

I just order stuff from right here and everything comes to my doorstep in a couple of days... propeller
Logged
Jimise
Don't pick it up by the candle!
Contributing NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 75
Offline Offline

Gender: Male
Posts: 752
« Reply #14 on: September 26, 2009, 06:15:44 PM »
Hello again, Well I got my bell hooked up today! And it is pretty loud  Tongue Out
There is a guy here in Lake Havasu with a small business called Havasu Slots.  Havasuslots.com 
Anyway, he had some wiring harnesses from some old machines and we pieced together a connector
that plugged in between the bell and the board (J14) So I did not have to cut anything!
Thanks to everyone on the board for the help!!      applause 
Logged
jaeckleint
Guest
« Reply #15 on: September 26, 2009, 06:28:44 PM »
Does he have another one? propeller propeller
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.09 seconds with 20 queries.