Welcome, Guest. Please login or register.
November 22, 2024, 08:50:42 AM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  General NLG Chat
| |-+  The Slot Shop **Tech Talk**
| | |-+  Burning 27c4002 with a GQ-4X burner		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Burning 27c4002 with a GQ-4X burner  (Read 5158 times)
jdkmunch
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 624
Offline Offline

Gender: Male
Posts: 2640
« on: February 23, 2010, 10:33:15 AM »
Hi-  I decided to create a new thread here - 

I have the GQ-4X burner with this pictured adapter.     

I have tried the chip in both sockets - with both jumper settings on each with no luck.   
The chips should be blank so when I go to read them it does go through the process and displays all FF's.  However I can do this with no chip installed so it really doesn't tell me anything.
 I'm afraid to put in my key chip because I don't want to screw it up.     What I'm going to do now is erase these chips again for about a half hour to make sure that there blank.

My question are:

1.  The socket on the left is larger than the chip but is labeled 27c400  so I'm ASSUMING that the 27c4002 goes in there.   Correct? (the top two sockets are empty with the chip in)
2.  It came with this cable.  Any idea what it's for? 

* photo.jpg (153.84 KB, 600x800 - viewed 322 times.)
Logged
Tilt
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 366
Offline Offline

Gender: Male
Posts: 724
« Reply #1 on: February 23, 2010, 12:24:22 PM »
27C400 is not the same as a 27C4002.  The 27C4002 is interchangeable with a 27C4096 though and the socket on the right has a label for 27C4096.  It's possible the 4002 was damaged in the left socket.  Do you have another (or 4096) that you can try?
Logged
jdkmunch
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 624
Offline Offline

Gender: Male
Posts: 2640
« Reply #2 on: February 23, 2010, 12:26:04 PM »
Yes I do!  - thank you that's why I wrote ASSUME!  I can't pick a winner in a one horse race.

now that I know I'll try to erase all the chips again and try each one in the right socket!
Logged
CaptainHappy
NLG Site Administrator
NLG Site Administrator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 622
Offline Offline

Gender: Male
Posts: 3203


I haven't met a Jackpot that I didn't like!!!
« Reply #3 on: February 23, 2010, 06:30:48 PM »
Tilt answered pretty quickly about the 27C4096 being the same as the 27c4002, but I thought that I would "ADDRESS" your other question about the cable. That cable is for different address lines that may need to be connected on some programmers, but not on this one as far as I know since I use a different 16bit adapter. HAPPY TESTING!!!

CH CaptainHappy
Logged
  Come sail away, Come sail away Come sail away with me..
jdkmunch
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 624
Offline Offline

Gender: Male
Posts: 2640
« Reply #4 on: February 23, 2010, 06:37:25 PM »
ok good to know - my plan of action will be to do a clean erase of the chips and then try again in the adapter on the right side of the card.

I wish I didn't have to work tonight  -  so I may not get a chance to try it out.    I'll try though.  yes
Logged
OhioGaming
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 297
Offline Offline

Posts: 834



WWW
« Reply #5 on: February 23, 2010, 08:33:53 PM »
Take it to work ...
Logged
jdkmunch
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 624
Offline Offline

Gender: Male
Posts: 2640
« Reply #6 on: February 23, 2010, 09:23:57 PM »
I thought about it but then I said it might be pushing it!  bust gut laughing

Sports awards start at 7 bbl!
Logged
laneman
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 55
Offline Offline

Gender: Male
Posts: 445
« Reply #7 on: July 11, 2010, 05:39:27 PM »
Heres what my adapter looks like for the 4002 chips.
I just bought this programmer,works really well so far.

* SUNP0002.JPG (399.57 KB, 1280x1024 - viewed 310 times.)
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.092 seconds with 20 queries.