Welcome, Guest. Please login or register.
November 23, 2024, 11:26:06 AM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  IGT S2000 and Vision Games.
| | |-+  S2000 Conversion "Big Times Pay" set-up		 0 Members and 4 Guests are viewing this topic. « previous next »
Pages: 1 2 3 [4] Go Down Print
Author Topic: S2000 Conversion "Big Times Pay" set-up  (Read 37783 times)
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #75 on: May 30, 2011, 04:55:09 PM »
My guess is that it's a switcher (CRxx's ) for the SMD lamps on the other side of it.
It looks like they put one between each pair of LED's?
The [Qxx's] look like timer IC's
while the [Rxx"s] look like resistor IC's...

Elaborating the rest of the IC's:
Uxx's (eproms)
Cxx's (capacitors)
Jxx's (connector headers..."Joints"?)
Fxx's ( no idea)
DSxx's (SMD LED's
L2 (no idea)
E1 (no idea)
RPxx's ( again, no idea)
MHxx's ( I'm guessing "Machine Hardware"? lol )
« Last Edit: October 25, 2011, 04:24:57 PM by stayouttadabunker » Logged
coorslight115
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 79
Offline Offline

Gender: Male
Posts: 2602
« Reply #76 on: May 30, 2011, 05:01:02 PM »
Quote from: stayouttadabunker on May 30, 2011, 04:49:35 PM
Nice hit...I'm RED WITH JEALOUSLY!!! rotflmao
Does your ring lights come on as the bonus wheel is spinning coors?


Yes they do

<a href="http://www.youtube.com/v/M3myMOR6v9E&rel=0" target="_blank">http://www.youtube.com/v/M3myMOR6v9E&rel=0</a>

<a href="http://www.youtube.com/v/9x1d98GdXjU&rel=0" target="_blank">http://www.youtube.com/v/9x1d98GdXjU&rel=0</a>
« Last Edit: May 30, 2011, 05:06:24 PM by coorslight115 » Logged
FORDSBS
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 363
Offline Offline

Gender: Male
Posts: 4162


PET
« Reply #77 on: May 30, 2011, 05:05:38 PM »
Quote from: coorslight115 on May 30, 2011, 01:28:53 PM
It can be saved, find the components and send it to me. I'll fix it up and send it back wave

Take my word for it. TIM CAN REPAIR IT.
Ford
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #78 on: May 30, 2011, 05:12:30 PM »
Oh...!
I don't doubt that Coors could indeed repair it Fordsbs!
It's just something I want to see if I could do is all...!
It's my personal machine and baby... Tongue Out
All the SMD LED's are good on this board...so THAT'S not it...
Photo below is of what's left of my pencil eraser after taking that black rubber ring off the circuit board....lol>>>

<a href="http://www.youtube.com/v/abemWEG1v5w&rel=0" target="_blank">http://www.youtube.com/v/abemWEG1v5w&rel=0</a>

* Removed SMD rubber glass protector.jpg (189.18 KB, 1451x1507 - viewed 363 times.)
« Last Edit: May 30, 2011, 06:32:05 PM by stayouttadabunker » Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #79 on: May 31, 2011, 03:36:46 PM »
Okay, I having a problem searching for a few IC components.
First of all, I don't know what I'm looking for...lol

From what I understand, the IC component's I need to repair this bonus reel light board are
surface mount aluminum electrolytic capacitors.
I cannot for the life of me figure out what the values are that are written on top of the cans.

The 1st one has this:
251
22
3.5 or 35

The 2nd one has this:
100
CFC
1PN

The second photo below is a screen shot from the mouser website ordering page.
Would anyone have any clues as to what values I should let the website search narrow it down to?
Click on any photo to enlarge...>>>

* Bonus Reel Light circuit board IC components 002.jpg (75.47 KB, 1024x768 - viewed 379 times.)

* Capacitor Dialog box choices.png (35.81 KB, 1002x360 - viewed 367 times.)
Logged
cowboygames
Abbys Dad
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 680
Offline Offline

Gender: Male
Posts: 3916


Happiness in life is a great dog
« Reply #80 on: May 31, 2011, 04:16:23 PM »
Hi Mark, your's aren't labeled the same as the ones I have on hand, but as a last resort you could lift them off the board and use a cap checker to see what the values are. I would bet 35v and whatever Mic value
Logged
coorslight115
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 79
Offline Offline

Gender: Male
Posts: 2602
« Reply #81 on: May 31, 2011, 06:11:14 PM »
Quote from: stayouttadabunker on May 31, 2011, 03:36:46 PM
Okay, I having a problem searching for a few IC components.
First of all, I don't know what I'm looking for...lol

From what I understand, the IC component's I need to repair this bonus reel light board are
surface mount aluminum electrolytic capacitors.
I cannot for the life of me figure out what the values are that are written on top of the cans.

The 1st one has this:
251
22
3.5 or 35

The 2nd one has this:
100
CFC
1PN

The second photo below is a screen shot from the mouser website ordering page.
Would anyone have any clues as to what values I should let the website search narrow it down to?
Click on any photo to enlarge...>>>


1st one is a 22uF 35v and the 2nd is a 100uF 35v. They are SMD Aluminum Electrolitic Caps. They come in letter sizes but with mouser it is just easier to measure your solder tab width and pick the one that matches. My son has a whole bunch of these, I will have him look for a few.
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #82 on: May 31, 2011, 06:33:10 PM »
Thanks coors...tell your son "Thanks from Stayouttadabunker" too!  yes
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #83 on: December 13, 2011, 06:32:52 PM »
Quote from: cowboygames on May 31, 2011, 04:16:23 PM
Hi Mark, your's aren't labeled the same as the ones I have on hand, but as a last resort you could lift them off the board and use a cap checker to see what the values are. I would bet 35v and whatever Mic value

I never thanked you Cowboy! Thanks!  applause Have a good holidays!
Logged
knagl
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 642
Offline Offline

Gender: Male
Posts: 5489


Kevin
« Reply #84 on: December 13, 2011, 06:54:59 PM »
Did you get it working then, Mark?
Logged
If you find this site helpful, please consider making a small donation to help defray the cost of hosting and bandwidth.

Please do not PM me for support or "how to" requests -- please post your request in the forum so that everyone may assist you and everyone can benefit from the answer to your question!  Thanks! Smiley
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #85 on: December 13, 2011, 07:18:57 PM »
Not this one yet,  no.
The cap I got from the boy has been sitting on my desk forever.  arrow
I just soldered it in but I know it's not going to work because there are a couple
of more missing resistors next to it in locations "L1" and "C5" that I have to get as well.

This Bonus reel Dazzle LED circuit board was mangled pretty good.
Somebody busted off three IC components in one shot.
How that happened I have no idea but would love to hear it!  rotflmao

I'll update you guys soon when I get it running.
Logged
Foster
The S2000 GURU
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 345
Offline Offline

Gender: Male
Posts: 2872
« Reply #86 on: December 13, 2011, 10:53:02 PM »
L1 should be an inductor and C5 would be a capacitor.
Logged
A Slot Machine and Coca-Cola Addict!!
"If it is not broke do not fix it" I keep forgetting that!
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #87 on: December 13, 2011, 11:07:11 PM »
Quote from: Foster on December 13, 2011, 10:53:02 PM
L1 should be an inductor and C5 would be a capacitor.

small tiny stuff...thanks for the info Foster!
Logged
Pages: 1 2 3 [4] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.119 seconds with 20 queries.