Welcome, Guest. Please login or register.
November 22, 2024, 02:08:21 AM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  General NLG Chat
| |-+  The Slot Shop **Tech Talk**
| | |-+  S2000 wobbling 2 inch reels		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: S2000 wobbling 2 inch reels  (Read 8005 times)
Buzz
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1158
Offline Offline

Gender: Male
Posts: 4641
« on: April 09, 2010, 03:59:49 PM »
Long story but here goes. I made a stop and brought back from AZ 3 five reel S2000 of the 15 total reels 10 were just junk I mean really worn out. Now being a Okie at heart and having Capt (up to his ass in tax papers) Happy's machine for a Guinea Pig this is the fix I did.

Remove reel basket from stepper motor ( mark basket and stepper motor shaft for when you reinstall )

On the stepper motor cross shaft you will see two small square plastic ( I'm going to call them drive blocks ) these blocks are the parts that are worn out

I took a Q tip and coated the inside of the basket ( where the drive blocks go )  with petroleum jelly ( also coated stepper shaft where it goes through the basket )

I then took RTV Silicone gasket maker (can be bought in just about any store you go in Auto Section ) and coated the cross shaft and the drive blocks with the silicone. I also coated the hole in the basket the stepper shaft goes through, but I don't think that step was needed.

Now just reassemble  It's a Bitch to get the basket down over the drive blocks. If you don't have it lined up perfect the blocks will turn on the cross shaft.

Now my reasoning for the Petroleum Jelly was,  it should keep the Silicone from sticking to the basket and stepper shaft. If I'm wrong and it does stick to the basket it will make future removeables difficult, But you know what I started with JUNK that needed to be replaced anyway.  I think if you could find a real FAT O ring and use it in place of the drive block would work or make a drive block out of rubber. Hard plastic was not a very good idea someone came up with!!
Logged
NLGs Motto  " IF IT AIN'T BROKE GIVE ME TIME IT WILL BE "
ashyron
In Remembrance of our lost NLG Members
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 255
Offline Offline

Gender: Male
Posts: 964


RIP Dad. I love you. 5-26-10


WWW
« Reply #1 on: April 09, 2010, 04:08:26 PM »
K+ to you Buzz.  I have not turned on the games here yet because everyone is still sleeping but I will let you know how it turned out.  It worked last night before I shut the games off to let that stuff dry.

That is something to mention too maybe??  After doing all the reels, let the silicone gasket stuff dry for a few hours, maybe overnight.  This way the stuff doesn't get smeared all over from the spinning reel when it's wet. 
Logged
Well, it's been almost 2 years.  I'm kinda back. Undecided
Buzz
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1158
Offline Offline

Gender: Male
Posts: 4641
« Reply #2 on: April 09, 2010, 04:30:21 PM »
Good point Ron I forgot all about that step. Must be HELL having CRS.  Cry Laughing Cry Laughing   The two machines Ron highjacked from me, we did this mod to them last night. hissy fit hissy fit hissy fit  On the tube it says " Let set one hour then retighten the bolts, fully cure in 24 hours " 
« Last Edit: April 09, 2010, 04:37:30 PM by Buzz » Logged
NLGs Motto  " IF IT AIN'T BROKE GIVE ME TIME IT WILL BE "
ashyron
In Remembrance of our lost NLG Members
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 255
Offline Offline

Gender: Male
Posts: 964


RIP Dad. I love you. 5-26-10


WWW
« Reply #3 on: April 09, 2010, 04:33:05 PM »
Quote from: Buzz on April 09, 2010, 04:30:21 PM
Good point Ron I forgot all about that step. Must be HELL having CRS.  Cry Laughing Cry Laughing   The two machines Ron highjacked from me, we did this mod to them last night. hissy fit hissy fit hissy fit

highjacked ?? bust gut laughing bust gut laughing bust gut laughing  Who loaded them into my truck??  Scratch Head bust gut laughing bust gut laughing

<ADD>  Wanna help me load a couple more?? arrow
« Last Edit: April 09, 2010, 04:47:53 PM by ashyron » Logged
Well, it's been almost 2 years.  I'm kinda back. Undecided
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #4 on: April 09, 2010, 04:37:22 PM »
You smell that rubber silicone burning on the hot fluorescent lights yet?  Tongue Out

I think it's a great fix providing you let everything sit and dry for a day.
Logged
Buzz
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1158
Offline Offline

Gender: Male
Posts: 4641
« Reply #5 on: April 09, 2010, 04:43:42 PM »
Bunker  It just happened, but I used High Temp silicone and I waited about  humm how long does it take a S2000 to boot up? That's how long I waited !!  But not what I recommend.  Cry Laughing
Logged
NLGs Motto  " IF IT AIN'T BROKE GIVE ME TIME IT WILL BE "
tacman
NLG Document, Media Gallery and FAQ Writer
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 446
Offline Offline

Gender: Male
Posts: 1537


Genius in training.
« Reply #6 on: April 09, 2010, 06:41:49 PM »
I remember getting neoprene rubber from a large office supply store, they use it for squeegees blades or something. This is much more sturdy than a regular rubber and if I remember correctly it was available in different widths. It worked very well for the application I used it for and may work for making the blocks.

 Dan (tacman)
Logged
CaptainHappy
NLG Site Administrator
NLG Site Administrator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 622
Offline Offline

Gender: Male
Posts: 3203


I haven't met a Jackpot that I didn't like!!!
« Reply #7 on: April 09, 2010, 06:55:50 PM »
Quote from: tacman on April 09, 2010, 06:41:49 PM
I remember getting neoprene rubberS from a large office supply store, they use it for squeegees blades or something. This is much more sturdy than a regular rubberS and if I remember correctly it was available in different widths. It worked very well for the application I used it for!!! Hippo Dance Super Hotdog hot Jeannie and may work for making the blocks.

 Dan (tacman)

Dan,

Sorry in advance for playing with your quote above, but I could not resist!!!  Cry Laughing Cry Laughing Cry Laughing

CH CaptainHappy
Logged
  Come sail away, Come sail away Come sail away with me..
jdkmunch
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 624
Offline Offline

Gender: Male
Posts: 2640
« Reply #8 on: April 09, 2010, 07:14:31 PM »
I remember reading that with the regular sized reels you could put black tape on the stem.  Can you do this with the 2" reels too?
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #9 on: April 10, 2010, 12:26:29 AM »
Quote from: jdkmunch on April 09, 2010, 07:14:31 PM
...you could put black tape on the stem. ...


Or duct tape? Wouldn't it be easier to pop a blue pill?






(It must be Friday night again... Tongue Out)
Logged
coorslight115
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 79
Offline Offline

Gender: Male
Posts: 2602
« Reply #10 on: April 10, 2010, 01:01:08 AM »
 Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Weird Eyes Weird Eyes Weird Eyes mooners mooners mooners mooners mooners Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Frosty Beer Pizza Pie Pizza Pie Pizza Pie Pizza Pie Pizza Pie Pizza Pie Pizza Pie Pizza Pie Pizza Pie Pizza Pie Pizza Pie

Party time !!!

Happy Friday !!

Beer and pizza compliments of me !!

Coorslight115  ....Enjoy! Crazy Crazy Crazy Crazy Crazy
Logged
Buzz
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1158
Offline Offline

Gender: Male
Posts: 4641
« Reply #11 on: April 10, 2010, 04:10:08 AM »
Quote from: jdkmunch on April 09, 2010, 07:14:31 PM
I remember reading that with the regular sized reels you could put black tape on the stem.  Can you do this with the 2" reels too?



Much  It's not the shaft going through basket that's worn, it is the part I called the drive blocks that need help. After I started this post I went in and tore apart a bonus reel from a S 2000 4 reel machine, looks just like a reel from a 5 reel machine. First Pic. is stepper motor shaft without drive blocks, second Pic with blocks

* PICT0047.sm.jpg (234.47 KB, 800x600 - viewed 307 times.)

* PICT0049.sm.jpg (277.11 KB, 800x600 - viewed 338 times.)
« Last Edit: September 27, 2010, 04:07:47 PM by Buzz » Logged
NLGs Motto  " IF IT AIN'T BROKE GIVE ME TIME IT WILL BE "
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #12 on: April 10, 2010, 11:53:46 AM »
Holy Crap!
They're made outta plastic?
How dumb is that?
Are they really needed to spin the reels?
Wouldn't the pin be sufficient enough?
I've never seen those.

No wonder you used silicone...I would have too.
Logged
ashyron
In Remembrance of our lost NLG Members
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 255
Offline Offline

Gender: Male
Posts: 964


RIP Dad. I love you. 5-26-10


WWW
« Reply #13 on: April 10, 2010, 04:56:01 PM »
Quote from: stayouttadabunker on April 10, 2010, 11:53:46 AM
Holy Crap!
They're made outta plastic?
How dumb is that?
Are they really needed to spin the reels?
Wouldn't the pin be sufficient enough?
I've never seen those.

No wonder you used silicone...I would have too.

Yea they are plastic.  It's kind of crazy how this was designed.  When Buzz took  one apart it had lots of plasticy gritt all over from the plastic blocks grinding against the basket where thay are all held together.  This little project has worked well.  We have only had two little problems since fixing these.  Two bulbs that weren't out, went out so I had bulbs to replace again.   Duh! Duh!  As far as the reels go they are working great with very little wabble. Hail Hail

Thanks again for the help Buzz.  I gotta give K+ to you again.
Logged
Well, it's been almost 2 years.  I'm kinda back. Undecided
jdkmunch
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 624
Offline Offline

Gender: Male
Posts: 2640
« Reply #14 on: April 10, 2010, 06:16:52 PM »
That's totally crazy how there plastic  Scratch Head
Logged
Crowsen
New NLG Member 1 to 100 Post
**

Total Karma Storms: 8
Offline Offline

Posts: 90


“When the going gets weird the weird turn proâ€
« Reply #15 on: May 20, 2010, 01:07:55 PM »
If your trying to stabalize the reel baskets have you tried ring stabilizers. In the past I have and still do work on S+ and S2000 and they work fairly well. I think the grease or jelly or what ever you used is a good idea just not in large quantities.
Logged
No man is so foolish but he may sometimes give another good counsel, and no man so wise that he may not easily err if he takes no other counsel than his own. He that is taught only by himself has a fool for a master.
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #16 on: May 20, 2010, 01:46:57 PM »
It would be very good if you could post a picture up here of one of these "Ring Stabilizers"...
I've never seen or heard of these... Scratch Head 3
Buzz used silicone...which hardens to a rubber-like consistency.
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.117 seconds with 19 queries.