Welcome, Guest. Please login or register.
November 21, 2024, 07:36:04 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  Monitor Repair Log and Database. **Arcade and Gaming**
| |-+  Monitor Repair Tech Support
| | |-+  Ceronix 2093 missing gun (Blue or green?) on startup		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Ceronix 2093 missing gun (Blue or green?) on startup  (Read 6039 times)
racergiant
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 105
Offline Offline

Gender: Male
Posts: 321
« on: September 16, 2008, 04:01:11 AM »
Started by hoppy -


Hi
my GK has a gun problem on start up . screen jump in and out of color then settles down ok after a few minutes.
I think its the blue gun as I would expect the screen to go to a purple colour if the green gun  had failed
I take it this is the start of futher faulting to come.
Is there an easy remedy, ie a faulty capacitor, If so where should I look for it .
When it is going the color purity tests from the screen menu are great. The screen had settled before I could access the test menu

Thank you for your replies.
Logged
racergiant
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 105
Offline Offline

Gender: Male
Posts: 321
« Reply #1 on: September 16, 2008, 04:01:30 AM »
By Habu -


I would suspect a bad solder joint on one of the video PRAs or the CRT socket.

Bruce.
Logged
racergiant
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 105
Offline Offline

Gender: Male
Posts: 321
« Reply #2 on: September 16, 2008, 04:01:48 AM »
By hoppy -


Thank you. sound like good solution for the problem. Will let you know how I get on later in the week.
Logged
racergiant
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 105
Offline Offline

Gender: Male
Posts: 321
« Reply #3 on: September 16, 2008, 04:02:19 AM »
By ESDAVE -


hi if your blue was at fault you would have a yellow picture, look on the neckboard/tube base for dry joints . check the R/G/B cathode voltages should be about 90volts but it can be a bit higher or lower   it depends on emission/ life of crt   , if you need more info please let me know. esdave uk engineer.
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.082 seconds with 19 queries.