Welcome, Guest. Please login or register.
November 02, 2024, 01:37:18 AM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  IGT S2000 and Vision Games.
| | |-+  General Reel Tilt
0 Members and 15 Guests are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: General Reel Tilt  (Read 5200 times)
FORDSBS
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 363
Offline Offline

Gender: Male
Posts: 4162


PET


« on: July 26, 2010, 09:15:38 PM »

Have a problem with an IGT S2000 5 reel. When I start up it goes into general reel tilt. I tried reset key & about every thing else.
It goes back into reel tilt. The only way to get it running again is to 5.1 reel strip test - run through full cycle. Then it it works. It
will work all day. When I turn it off (which I use a surge strip & do not open door) It will go into general reel tilt when i turn it on. Do reel test &
it will work OK until I turn it off. Driving me nuts.
any help appreciated.
Ford
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447



« Reply #1 on: July 26, 2010, 09:35:42 PM »

Check your MPU battery.
I'd start looking around for a spare board as well...
Logged
FORDSBS
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 363
Offline Offline

Gender: Male
Posts: 4162


PET


« Reply #2 on: July 26, 2010, 09:39:02 PM »

battery ok. I was afraid it was the board.
I may as well check with Jim and see if he has one.
Thanks--even if it's bad news.
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447



« Reply #3 on: July 26, 2010, 09:41:24 PM »

Are all the reels strips on tight?
If one is loose, and touching the reel glass - it will tilt too.
Exactly what code are you getting in your LCD/ vacuum display panel?
Logged
FORDSBS
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 363
Offline Offline

Gender: Male
Posts: 4162


PET


« Reply #4 on: July 26, 2010, 09:52:55 PM »

strips are tight and not rubbing. If they would it not keep operating good for hours with no trouble after i run reel test.
call attendant
general reel tilt
I thought maybe battery since I turn it on and goes into reel tilt. If I turn it off and back on right away it will be ok.
If I turn it off 1/2 hr. I will go into reel tilt. That's why I was hopping battery.
Logged
FORDSBS
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 363
Offline Offline

Gender: Male
Posts: 4162


PET


« Reply #5 on: July 26, 2010, 09:59:56 PM »

Maybe I should try another battery first. Can't hurt
It reeds 2.61--the same as the other 3 I have.
Logged
Yoeddy1
The OCD kit hoarder
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 233
Offline Offline

Gender: Male
Posts: 3280



WWW
« Reply #6 on: July 26, 2010, 10:09:19 PM »

For what it's worth, I fought some misc errors a year ago with my old S+ and it ended up being a bent pin on a cable connector to the MPU.  I was getting battery errors, reel errors, etc, and some days it would work for hours, sometimes minutes, with or without a new battery.  Drove me crazy.  Once I straightend it out with pliers, never had a problem again.
Logged


Yoeddy's IGT Slot Machine Videos
http://www.youtube.com/user/Yoeddy1
FORDSBS
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 363
Offline Offline

Gender: Male
Posts: 4162


PET


« Reply #7 on: July 26, 2010, 10:15:43 PM »

Thanks, I'll check. Anything is worth a try.
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447



« Reply #8 on: July 26, 2010, 10:16:47 PM »

Good stuff Yoeddy1!  applause
You may be on the right track.
Pins CAN get bent if the MPU is handled a little rough.

More likely though, depending on where the machine was stored &
while it was away from the controlled enviroment of a casino floor, it's possible
that dampness may have corroded certain female and male receptor pins
in the machines' connectors somewhere.
It's helpful at times to pull connectors apart and push them back together
to rub off a little of the corrosion and oxidization that can accumulate onto the contacts.
Reho33 of PA has sworn that the stuff he has called "Deoxit" - works wonders!
I still want to get some and try it on my connectors.!!!  yummy yummy

As far as the onboard watch-like flat battery, I think it has to
drop under 2.2 volts ( I'm not sure of the exact low voltage point)
in order for the machine to send out a low battery error code to the display panel.

The reason why I said to check it is because it seems that your
machine tilts when powering up.
So you go into the tests and get it all back in order and it works
a while - until you shut off the machine.

When the machine is powered off - this is when the onboard battery
springs into action - to save the machines' settings.
If at any point the battery drops below a certain threshold -
the machine starts acting crazy.
Logged
FORDSBS
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 363
Offline Offline

Gender: Male
Posts: 4162


PET


« Reply #9 on: July 26, 2010, 10:25:19 PM »

Thanks Bunker & Eddy.
That will keep me out of trouble for awhile. Going to go over all connections.
Logged
reho33
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 146
Offline Offline

Gender: Male
Posts: 1594


Slot Losers of America / Tokie Owens


« Reply #10 on: July 27, 2010, 12:03:07 AM »

Here is the link:   http://www.caig.com/   Worth it's weight in gold............ applause
Logged

** NOTE: The information contained in any of my posts relating to slot machine ownership and use is information that I have gathered from publicly known sources correspondingly under the same protections of Free Speech governed under the Laws of the United States and Canada and is for informational use only. As is my Constitutional Right under United States and Canadian Laws the redistribution of said information is considered a form of free speech. Using this information in the United States or Canada to conduct illegal gambling in states/provinces where it is unlawful has been declared against the law in those states/jurisdictions and as such I do not advocate the illegal use of such information under both the United States and Canadian Laws. All references and examples of personal experiences are hypothetical in nature, and it is up to you to determine if the information presented is applicable to your situation or not**
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447



« Reply #11 on: July 27, 2010, 12:58:07 AM »

That's the stuff!!!

Thanks for the look at it reho!  applause
Logged
Bettor Slots
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 751
Offline Offline

Gender: Male
Posts: 1946



WWW
« Reply #12 on: July 27, 2010, 01:12:45 AM »

I have run into this several times now and most of the time it ended up being a short in the reel harness....it's very hard to track down the culprit too.  It's odd too, because like you said you can go into I/O tests and spin the reels and then they run...so is there a surge or lack of surge during power up that causes the communication failure?
Logged

If life is like a box of chocolates....why do I always seem to end up with the butter creme?
FORDSBS
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 363
Offline Offline

Gender: Male
Posts: 4162


PET


« Reply #13 on: July 28, 2010, 10:24:03 AM »

Got it working. Hope it continues. Turned it on & off for last 20 hrs. & it keeps working.
 Worked on 1 area @ a time so I'd know where it was. Started w/MPU.
Pulled most things from MPU & cleaned everything. Dried off - put in & it worked.
Don't know what for sure  but it was on MPU.
Thanks for all help & advice.
Ford
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447



« Reply #14 on: July 28, 2010, 01:40:45 PM »

Probably a loosely seated eprom chip leg.

I had an error [62-0] on a machine. ("Bad Game Prom")
I knew that there was nothing wrong with that prom.
So I pulled it out and reseated it into the socket nice and easy.
Then I turned the machine on and haven't had a problem with it since.
Logged
FORDSBS
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 363
Offline Offline

Gender: Male
Posts: 4162


PET


« Reply #15 on: July 28, 2010, 01:44:51 PM »

Don't know for sure what on MPU but I took all out and sprayed w/cleaner
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447



« Reply #16 on: July 28, 2010, 01:50:49 PM »

I actually took an S+ motherboard and ran it under warm water in the kitchen sink.
I let it dry for a couple of days and ran my wife's high speed hair dryer
on everything on the motherboard just to make sure no water remained
trapped in the main connectors anywhere.
I didn't see any visible liquid so I threw it into the machine and that works like a charm!
Sometimes our babies just need a good cleaning!  rotflmao
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  


If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com    Newlifegames.net    Newlifegames.org
   New Life Games    NewLifeGames  NLG  We Bring new Life to old Games    1-888-NLG-SLOTS
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.123 seconds with 19 queries.