Welcome, Guest. Please login or register.
November 23, 2024, 04:45:59 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  Bally Electromechanical
| | |-+  problems with E-2237-8		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: 1 [2] Go Down Print
Author Topic: problems with E-2237-8  (Read 16835 times)
MarkInAz
Jack of all, master on none.
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 22
Offline Offline

Gender: Male
Posts: 344
« Reply #25 on: August 28, 2010, 01:27:56 AM »
Hi Bob.  Glad the hopper motor is good.  Yes, it may be the hopper controll board is bad, but you say the machine makes a noise when it should start paying out?  Can you tell where the noise is coming from?  Backing up a little bit- I wonder if the 110 V is getting to the hopper assembly along with the other signals via the connector in the rear.  If the noise is coming from the hopper then that would tell me the voltages probably are.  You can try this  stir the pot / get cooking - remove the hopper, put in a box to catch the coins, play the game and listen for the noise again.  I'm betting its the control board though.  Do you need the schematics?

Cheers- Mark     
Logged
Its Always Something...
rjpohl
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 103
Offline Offline

Gender: Male
Posts: 726



WWW
« Reply #26 on: August 28, 2010, 05:30:01 PM »
When I said it made a nosie it's a bell/tilt sound and not a mechanical nosie. 
Logged

http://samronslots.com/
MarkInAz
Jack of all, master on none.
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 22
Offline Offline

Gender: Male
Posts: 344
« Reply #27 on: August 29, 2010, 03:20:06 PM »
OK, I understand  Duh! .  I'd swap out the controll board, odds are high that is the problem.
Logged
Its Always Something...
rjpohl
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 103
Offline Offline

Gender: Male
Posts: 726



WWW
« Reply #28 on: September 17, 2010, 09:26:55 AM »
anyone have a hopper board and door lock assemble for sale?
Logged

http://samronslots.com/
rjpohl
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 103
Offline Offline

Gender: Male
Posts: 726



WWW
« Reply #29 on: September 28, 2010, 09:38:03 AM »
I received the hopper board from Foxsslots1 and after installing the slot is working perfectly.

A big thanks to Barry Fox and MarkInAx,  I really enjoying working on these older Bally machines but would be lost without your help.

Bob
Logged

http://samronslots.com/
MarkInAz
Jack of all, master on none.
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 22
Offline Offline

Gender: Male
Posts: 344
« Reply #30 on: September 28, 2010, 10:02:48 PM »
Great!  applause  Yup, its always satisfying when you finally get them up & running. 
Logged
Its Always Something...
rjpohl
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 103
Offline Offline

Gender: Male
Posts: 726



WWW
« Reply #31 on: October 06, 2010, 10:28:47 PM »
CRAP!

was working perfectly for a couple of days, now as soon as I turn the key on the door it goes into tilt (closing door doesn't cause the tilt, tilt happens when key is turned to lock position.  I can open door and a press reset, tilt light goes off, shut door, turn key and back to tilt.  only code on door is 50.

with the door open it periodically will go through a cycle where the coin mech energies, drops out, the coin out flap (below coin mech) shuts for a split second and finally the coin on the handle mech pulls in for a split second. 

hope someone can help.
thanks
Bob
Logged

http://samronslots.com/
MarkInAz
Jack of all, master on none.
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 22
Offline Offline

Gender: Male
Posts: 344
« Reply #32 on: October 14, 2010, 04:41:18 AM »
Hi Bob,

Take a look at both your door lock switch and your door hinge switch.  Also, you can do test #3 and check if the MPU "sees" them working.

Mark
Logged
Its Always Something...
rjpohl
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 103
Offline Offline

Gender: Male
Posts: 726



WWW
« Reply #33 on: October 14, 2010, 10:52:39 AM »
it's working again with the thanks of Barry, re-seated the CMOS chips and all was fine.
Logged

http://samronslots.com/
MarkInAz
Jack of all, master on none.
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 22
Offline Offline

Gender: Male
Posts: 344
« Reply #34 on: October 14, 2010, 02:52:20 PM »
 Jumping for Joey
Logged
Its Always Something...
Pages: 1 [2] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.113 seconds with 20 queries.