Welcome, Guest. Please login or register.
November 22, 2024, 06:46:36 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  Bally Reel Games. (Moderator: a69mopar)
| | |-+  Bally 6000 Bill Validator Problems		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Bally 6000 Bill Validator Problems  (Read 7378 times)
morspeed
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 12
Offline Offline

Gender: Male
Posts: 470
« on: August 14, 2010, 01:12:46 AM »
Anybody had any problems with Bally 6000 BV's?? I put in a known BV from an S2000, software changed of course, 13-ss by the way, Power everything up, BV Runs cycle and machine starts and is ready to play but green lights (arrows) are not on and won't accept bills.  No error codes and insert credit light is blinking. I cleared the machine twice hoping for a fix but no Luck!!! ARRRGH! banghead Weird thing is I had this happen on another machine and and finally it started working but don't remember what I did. Any thoughts??? Oh one other thing I was trying to get hand pay to work on these machines a while back and a69mopar had told me to change a few settings (61=2, 56= 0) but when I changed 56 to 0 the machine would not accept bills until I changed it back. (this was another machine) So is there possibly a setting I am missing like that?  Normally a clear would fix this though I would think...
Thanks,
Tommy
Logged
reho33
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 146
Offline Offline

Gender: Male
Posts: 1594


Slot Losers of America / Tokie Owens
« Reply #1 on: August 14, 2010, 01:14:36 AM »
The ID on the IGT is different than the one on the Bally
Logged
** NOTE: The information contained in any of my posts relating to slot machine ownership and use is information that I have gathered from publicly known sources correspondingly under the same protections of Free Speech governed under the Laws of the United States and Canada and is for informational use only. As is my Constitutional Right under United States and Canadian Laws the redistribution of said information is considered a form of free speech. Using this information in the United States or Canada to conduct illegal gambling in states/provinces where it is unlawful has been declared against the law in those states/jurisdictions and as such I do not advocate the illegal use of such information under both the United States and Canadian Laws. All references and examples of personal experiences are hypothetical in nature, and it is up to you to determine if the information presented is applicable to your situation or not**
a69mopar
647-402-1977
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 600
Offline Offline

Gender: Male
Posts: 3508



WWW
« Reply #2 on: August 14, 2010, 01:22:36 AM »
turn on(flip up) the chrome coin mech switch on the front of the mpu

W
Logged
         www.GTASLOTS.com      647-402-1977              BALLY S6000 GALLERY
morspeed
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 12
Offline Offline

Gender: Male
Posts: 470
« Reply #3 on: August 14, 2010, 01:59:39 AM »
Thank you again Wyane for making me feel like an idiot! Live and learn I guess. K+ to you.
Thanks,
Tommy
Logged
morspeed
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 12
Offline Offline

Gender: Male
Posts: 470
« Reply #4 on: August 14, 2010, 02:07:35 AM »
By the way, What is that switch for? If I add coin handling do I need to change that switch? Or leave it for both coin and bills?
Thanks,
Tommy
Logged
a69mopar
647-402-1977
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 600
Offline Offline

Gender: Male
Posts: 3508



WWW
« Reply #5 on: August 14, 2010, 02:28:39 AM »
the switch shuts of coin and bill acceptance.  It is good to use if you don't want anyone to play the machine but want to leave it turned on.

Thanks,
Wayne
Logged
         www.GTASLOTS.com      647-402-1977              BALLY S6000 GALLERY
morspeed
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 12
Offline Offline

Gender: Male
Posts: 470
« Reply #6 on: August 14, 2010, 03:18:53 AM »
How do I see your Bally 6000 Gallery?
Tommy
Logged
a69mopar
647-402-1977
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 600
Offline Offline

Gender: Male
Posts: 3508



WWW
« Reply #7 on: August 14, 2010, 03:38:03 AM »
I think you have to be on my buddy list.  I didn't intend it that wy, that's just how it is set up I guess.

Thanks,
Wayne
Logged
         www.GTASLOTS.com      647-402-1977              BALLY S6000 GALLERY
morspeed
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 12
Offline Offline

Gender: Male
Posts: 470
« Reply #8 on: August 14, 2010, 04:21:29 AM »
Wayne,

Do you know anything about setting up the coin handling? I am a little stumped. I picked up an optic from Terry but they did not send me the back prism. When I inquired Randy said there was no back to the coin optic but the manual states otherwise. Also I had a harness that was on another machine but there was no place to plug in the optic just the comparator.  (first Picture) and there was one in the machine but does not have as many wires that plug into the comparator (second Picture) and it doesn't turn on. I think I need a new harness.  Are there certain settings that need to bew made on the Bally as Well?

* P8130441.JPG (262.8 KB, 1280x960 - viewed 514 times.)

* P8130443.JPG (286.75 KB, 1280x960 - viewed 416 times.)
Logged
morspeed
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 12
Offline Offline

Gender: Male
Posts: 470
« Reply #9 on: August 14, 2010, 04:21:58 AM »
Optic

* P8130444.JPG (277.86 KB, 1280x960 - viewed 524 times.)
Logged
a69mopar
647-402-1977
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 600
Offline Offline

Gender: Male
Posts: 3508



WWW
« Reply #10 on: August 14, 2010, 05:00:35 AM »
The prism is attached as seen in the pic, well on the other side of it.  check the repair job on your harness, maybe you'll find a bad joint.

Thanks,
Wayne

* s6000 coin parts optic area prism.jpg (742.96 KB, 3244x1227 - viewed 475 times.)
Logged
         www.GTASLOTS.com      647-402-1977              BALLY S6000 GALLERY
morspeed
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 12
Offline Offline

Gender: Male
Posts: 470
« Reply #11 on: August 14, 2010, 05:08:59 AM »
Yeah I see it through the holes I don't have that I need to get one. Also the harness was not originally like that I was trying something but it still did not work before. On the first one there are five wires, on the second only three. When I hook up the first one with five the light comes on on the comparator. When I use the three wire one it does not.  The weird thing is what is the first harness for seeing how it does not have a tail for the Optic? Also what is that plate towards the end with the hole in it? Do I really need that? Never mind is that an insulator? I insulated the screws.
Tommy
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #12 on: August 14, 2010, 10:32:18 AM »
I find those prisms hard to find.
I need to search for an alternative.
Could I make one out of a couple pieces of mirrors?
or would that be blowing smoke?
Logged
a69mopar
647-402-1977
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 600
Offline Offline

Gender: Male
Posts: 3508



WWW
« Reply #13 on: August 14, 2010, 11:20:12 AM »
Quote from: stayouttadabunker on August 14, 2010, 10:32:18 AM
I find those prisms hard to find.
I need to search for an alternative.
Could I make one out of a couple pieces of mirrors?
or would that be blowing smoke?
I suppose if the mirrors were at the proper angles, they may work.
Logged
         www.GTASLOTS.com      647-402-1977              BALLY S6000 GALLERY
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.122 seconds with 20 queries.