Welcome, Guest. Please login or register.
October 31, 2024, 09:09:45 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Video Slots** Gaming machines
| |-+  BALLY Game Maker. (Moderator: tacman)
| | |-+  Newbie needs help..
0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] 2 Go Down Print
Author Topic: Newbie needs help..  (Read 15098 times)
jeemann99
Guest
« on: October 27, 2010, 12:48:06 AM »

I am TOTALLY new to slot / gaming machines.

I bought a 7200 Game Maker upright and had some game on there I want remove (Keno) dont even know how to play them. I bought some game maker games from Ebay and try loading them on one of the empty eprom sets on the board and when I turned it on it said something about a clear chip???? I have 5 Keno games on there now that I want to remove, but how do I know which chips they are and do some of them take 2? I bought 5 games that I want to add what do I need to do to make these work. Man this is frustratrating.

If someone lives in chicagoland I would be willing to pay them to do this

Any help would be appreciated thanks in advance

Total newb
Logged
StatFreak
rotaredoM etiS GLN labolG
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 756
Offline Offline

Gender: Male
Posts: 8549


Warning! Spammers will be eaten, with relish!


« Reply #1 on: October 27, 2010, 05:15:01 AM »

Welcome to NLG jeemann99 wave

Yes, you need a clear chip, which you can purchase from one of our vendors. If you look at this same board (where you started your new thread) you will find the answer is stickied two threads from the top. I recommend reading the top three threads and downloading the documents that they contain and/or point to to get up to speed on the Gamemaker.

StatFreak garfield
nlg  Global Moderator
Logged

I found myself at NLG garfield  ..but got lost again on the way home. Scratch Head 2
If found, please email me to myself. Thanks. yes
       Executive member in good standing of Rick's SMAA.                              Ehhh...What's Up Doc?
FORDSBS
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 363
Offline Offline

Gender: Male
Posts: 4162


PET


« Reply #2 on: October 27, 2010, 10:40:15 AM »

Check your email. I send you a manual.
Ford
Logged
jeemann99
Guest
« Reply #3 on: November 01, 2010, 09:34:48 PM »

I read the manual, but still do not understand where to place new game chips. The only slot I have open is P9 I put the new chip in there and it says to add clear chip. I did not have one and if I did where would I put that and why. I know picked up a clear chip from ebay,. but still do not know what to do. Do some games take multiple eproms? please help I bought these games but cannot get them working
Logged
FORDSBS
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 363
Offline Offline

Gender: Male
Posts: 4162


PET


« Reply #4 on: November 01, 2010, 09:49:20 PM »

Check this post out, it should help you.
http://newlifegames.net/nlg/index.php?topic=163.0
Ford
Logged
StatFreak
rotaredoM etiS GLN labolG
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 756
Offline Offline

Gender: Male
Posts: 8549


Warning! Spammers will be eaten, with relish!


« Reply #5 on: November 01, 2010, 10:01:22 PM »

Check this post out, it should help you.
http://newlifegames.net/nlg/index.php?topic=163.0
Ford


That would be one of those top three stickied threads I mentioned.. Scratch Head 3  Tongue Out

The clear chip goes in P10, and you have to remove the game that's in there to do the clear. You then put it (or another game) back after the clear. The machine will tell you when to do this on the screen.
Logged

I found myself at NLG garfield  ..but got lost again on the way home. Scratch Head 2
If found, please email me to myself. Thanks. yes
       Executive member in good standing of Rick's SMAA.                              Ehhh...What's Up Doc?
dpalmi
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 291
Offline Offline

Gender: Male
Posts: 819



WWW
« Reply #6 on: November 01, 2010, 10:33:02 PM »

Do some games take multiple eproms?

Yes - some Gamemaker games do require more than 1 eprom.

Dan #2
Logged

A great man once said, "I was told last time I would get a piece of cake."

tacman
Topic Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 446
Offline Offline

Gender: Male
Posts: 1537


Genius in training.


« Reply #7 on: November 01, 2010, 11:28:45 PM »

jeemann99, here is a Bally Gamemaker game change procedure with pictures attached below. Hope it helps.

 Dan (tacman)

* BALLY_GAMEMAKER_GAME_CHANGE.doc (2655 KB - downloaded 253 times.)
Logged

jeemann99
Guest
« Reply #8 on: November 02, 2010, 02:08:41 AM »

When I purchased the game the only port open was P9

I did the above until I ran into the problem where there was a game chip in P10,

- I removed a game in P5 inserted my new chip
- Insert Clear chip came on screen
- I installed clear chip in P10, but there was game in it and I do not know how to DO A MAINS CLEAR, so I just removed it and put in the clear chip
- When I put the board back in it says insert clear chip???????????
- So I put everything back to original and now I get a screen message "PLEASE INSTALL CLEAR CHIP MINIMUM AND MAXIMUM WAGE SETTINGS MUST BE CONFIGURED"

THIS SUX. DOES ANYBODY LIVE IN CHICAGOLAND THAT I CAN PAY TO DO THIS OR IF I CAN SEND IT OUT TO GET DONE


* bally.jpg (802.17 KB, 1600x1200 - viewed 359 times.)
Logged
StatFreak
rotaredoM etiS GLN labolG
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 756
Offline Offline

Gender: Male
Posts: 8549


Warning! Spammers will be eaten, with relish!


« Reply #9 on: November 02, 2010, 02:25:56 AM »

If you have single chip games, you can basically put them in any of the 10 sockets that you want, although it's best practice to start from P1 and go to P10, leaving the upper sockets empty if you choose to have fewer than 10 games in the machine.

If you have fewer than 10 games in the machine and want to swap some games, you CAN do it with only a partial clear by putting the clear chip in any free socket and performing a partial clear, but the trade off is that you cannot put a game back into the socket you used for the clear chip (so you can't do this and have more than 9 games.) It sounds like that is what is happening to you.

The better practice is to do a FULL clear. This requires that the clear chip be in P10, and you will be able to replace it with a game chip before setting up the machine after the clear. You will have to setup all options on the machine from scratch, but it's not that hard once you try it a few times, and it can even be fun because it allows you to try different setups to see how you like your machine configured. Follow the procedures outlined in the documents you downloaded and also follow the directions presented on the screen.

To do a full clear, you need to turn on switches 7 AND 8 on DIPSW1. Put the game chips that you will want in your machine in positions P1 through P9 in the order that you would like to see them on the menu screen, and put the clear chip in P10. Put the board in and power up the machine. Then follow the directions. Some Mains will run through the initial setup before telling you to remove the clear chip, others will have you remove it immediately. Just follow the prompts. When you do remove the chip, turn off the DIP switches and put the last game chip in P10, replace the board, power up, and continue to follow the prompts to complete the setup.
Logged

I found myself at NLG garfield  ..but got lost again on the way home. Scratch Head 2
If found, please email me to myself. Thanks. yes
       Executive member in good standing of Rick's SMAA.                              Ehhh...What's Up Doc?
jeemann99
Guest
« Reply #10 on: November 02, 2010, 02:38:39 AM »

I did that

I put my dip switches on "up" 7 and 8

Put in the games with the clear chip on P10 and I get the same message as above photo
Logged
StatFreak
rotaredoM etiS GLN labolG
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 756
Offline Offline

Gender: Male
Posts: 8549


Warning! Spammers will be eaten, with relish!


« Reply #11 on: November 02, 2010, 02:48:21 AM »

It sounds like you have a bad clear chip.

Just to cover the bases, are you installing your chips with the notch pointed in the correct direction to match the socket notch and the diagrams on the board? Are you sure that all of the chips are correctly inserted with no bent or broken pins, especially the clear chip? When you put in a 28 pin (512k) chip such as the clear and many poker games, are you matching the bottom end of the chips with the end of the socket, so that the empty socket holes are above the notch?
Logged

I found myself at NLG garfield  ..but got lost again on the way home. Scratch Head 2
If found, please email me to myself. Thanks. yes
       Executive member in good standing of Rick's SMAA.                              Ehhh...What's Up Doc?
jeemann99
Guest
« Reply #12 on: November 02, 2010, 03:12:47 AM »

yes, maybe a bad clear chip. do you know hwer I can get one besides Ebay that will deliver to Illinois
Logged
StatFreak
rotaredoM etiS GLN labolG
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 756
Offline Offline

Gender: Male
Posts: 8549


Warning! Spammers will be eaten, with relish!


« Reply #13 on: November 02, 2010, 03:23:50 AM »

Place an ad in our classified section and one of our vendors will get back to you.

One last thing. Have you checked your battery voltage? It should be over 3.0v (they are 3.6v, so 3.7 is full) . If not, that could be part of your problem.

Also, if you put the original chips back in their original positions and turn off the dip switches, I believe that your old games should come back up. It's possible that they won't, but if they do, you could play the machine until the new clear chip arrives.
Logged

I found myself at NLG garfield  ..but got lost again on the way home. Scratch Head 2
If found, please email me to myself. Thanks. yes
       Executive member in good standing of Rick's SMAA.                              Ehhh...What's Up Doc?
jeemann99
Guest
« Reply #14 on: November 02, 2010, 09:38:47 AM »

Do I need to pull all the Game Eproms out of P1 - P9 then put in Clear CHip in P10 set dips 7 and 8 on. Or do I just leave the games in P1 - P9. To do a full clear
Logged
JOHN42355
Rudys Gaming And Electronics LLC.
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 168
Offline Offline

Posts: 161


RudysDeals.com Gaming and Electronic Parts


WWW
« Reply #15 on: November 02, 2010, 10:34:09 AM »

No , Just pull P-10 and install the Clear. hope this helps
Logged

Discount Gaming Supplies And Free Manual Downloads At RudysDeals.com
FORDSBS
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 363
Offline Offline

Gender: Male
Posts: 4162


PET


« Reply #16 on: November 02, 2010, 10:37:47 AM »

Make sure you don't put the chip in backwards. Watch where your notch goes.
I put one in the wrong way a screwed it up.
Logged
JOHN42355
Rudys Gaming And Electronics LLC.
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 168
Offline Offline

Posts: 161


RudysDeals.com Gaming and Electronic Parts


WWW
« Reply #17 on: November 02, 2010, 10:58:14 AM »

Ford , You are right!! Sorry that I did forget That Important Information... frying pan
Logged

Discount Gaming Supplies And Free Manual Downloads At RudysDeals.com
jeemann99
Guest
« Reply #18 on: November 02, 2010, 11:52:58 AM »

chip was installed correctly and all pins were inserted
Logged
jeemann99
Guest
« Reply #19 on: November 02, 2010, 03:53:57 PM »

Ok I was using the wrong Dip Switches, so I now put the DPSW-1 # 7and 8 up and turn on machine. Now I get this message, so I put the dipswitches back down on 7 and 8 and I get the previous screen again



* bally 2.jpg (791.66 KB, 1600x1200 - viewed 335 times.)

* bally.jpg (802.17 KB, 1600x1200 - viewed 348 times.)
Logged
FORDSBS
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 363
Offline Offline

Gender: Male
Posts: 4162


PET


« Reply #20 on: November 02, 2010, 04:09:03 PM »

What happens when you turn off --put clear chip in & restart?
Logged
jeemann99
Guest
« Reply #21 on: November 02, 2010, 04:27:49 PM »

After I put in the clear chip I get this message. I am pointing to a bad cleear chip. I just ordered a new one.



* bally.jpg (802.17 KB, 1600x1200 - viewed 347 times.)
Logged
FORDSBS
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 363
Offline Offline

Gender: Male
Posts: 4162


PET


« Reply #22 on: November 02, 2010, 04:33:34 PM »

I think what you have is what I had on mine. Jim from Blue Ridge got me a debug chip & that fixed me up.
Check with Jim. He is good on these. slotwholesaler@aol.com
Logged
jeemann99
Guest
« Reply #23 on: November 02, 2010, 04:39:15 PM »

thanks I just sent an email
Logged
FORDSBS
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 363
Offline Offline

Gender: Male
Posts: 4162


PET


« Reply #24 on: November 02, 2010, 04:42:29 PM »

Keep in touch how your doing. That is what this site is about, helping each other. I don't know what these other guy's do but I'll try and help you get going.
Good luck, Ford
I wish you were closer to me & I'd help you set it up.
Logged
Pages: [1] 2 Go Up Print 
« previous next »
Jump to:  


If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com    Newlifegames.net    Newlifegames.org
   New Life Games    NewLifeGames  NLG  We Bring new Life to old Games    1-888-NLG-SLOTS
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.427 seconds with 21 queries.