Welcome, Guest. Please login or register.
November 22, 2024, 11:16:36 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  IGT S and S-plus Reel Games. (Moderator: knagl)
| | |-+  S PLUS BILL VALIDATOR DEAD		 0 Members and 2 Guests are viewing this topic. « previous next »
Pages: 1 2 [3] 4 Go Down Print
Author Topic: S PLUS BILL VALIDATOR DEAD  (Read 31093 times)
poppo
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 248
Offline Offline

Gender: Male
Posts: 3266
« Reply #50 on: August 17, 2011, 07:05:35 PM »
Quote from: shortrackskater on August 17, 2011, 06:37:45 PM
Only question is: what's U18? I am replacing from the old board to the new board as well, but I don't know what it does.

U18 is used for SAS and EFT communications. Unless you are playing around with trying to get SAS working, you don't need it.
Logged
proten
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 210
Offline Offline

Gender: Male
Posts: 1130
« Reply #51 on: August 17, 2011, 07:08:10 PM »
is it possible that the mother board cooked too?
Logged
One step at a time.
shortrackskater
NLG Site Administrator
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 192
Offline Offline

Gender: Male
Posts: 845


Insert Coin
« Reply #52 on: August 17, 2011, 07:09:28 PM »
It looks undamaged to me and again, there was an error code when I last shut this off...
Logged
poppo
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 248
Offline Offline

Gender: Male
Posts: 3266
« Reply #53 on: August 17, 2011, 07:09:38 PM »
Quote from: shortrackskater on August 17, 2011, 07:04:14 PM
Everything is in...powered on - the BV cycled, the reels moved slightly but no initial cycle and no error codes. When I shut this off (after cooking) it did have an error code but now there's nothing. I checked the dip switches and sure the IC's were seated and in the proper direction!

Make sure there are no pins bent on the MPU plugs. Also make sure the transformer on the tray is plugged in correctly (not offest). Also make sure the MPU is seated good. Some you have to really push down hard to get them to seat all of the way.

Are you getting any display at all?

Game and reel chips in the right sockets?
Logged
shortrackskater
NLG Site Administrator
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 192
Offline Offline

Gender: Male
Posts: 845


Insert Coin
« Reply #54 on: August 17, 2011, 07:18:48 PM »
No bent pins, seated properly, ic's in correct sockets. Nothing...no display but BV cycles.
Logged
poppo
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 248
Offline Offline

Gender: Male
Posts: 3266
« Reply #55 on: August 17, 2011, 07:21:53 PM »
I know you probably already did this, but check all of the fuses again and the fuse holder caps.

Also, you might try leaving that pesky 9 pin BV cable unplugged in the off chance the BV is cooked and somehow messing with the MPU. Process of elimination.
Logged
shortrackskater
NLG Site Administrator
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 192
Offline Offline

Gender: Male
Posts: 845


Insert Coin
« Reply #56 on: August 17, 2011, 07:23:41 PM »
Just did! I didn't really examine the caps...i'll do that now
Logged
shortrackskater
NLG Site Administrator
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 192
Offline Offline

Gender: Male
Posts: 845


Insert Coin
« Reply #57 on: August 17, 2011, 07:33:30 PM »
I don't see anything wrong with the caps either...???
Logged
poppo
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 248
Offline Offline

Gender: Male
Posts: 3266
« Reply #58 on: August 17, 2011, 07:38:08 PM »
I would remove all of the chips you transfered, and check all of the legs again and then re-seat them. Might even use the CMOS from your old board (just in case the other one is bad or something). One bent pin os all it will take to make it not boot.

If your board has jumpers by the game and reel chips, make sure both are set the same way.

It's possible your new board is bad. I don't think there is anything else really wrong with the machine since you did get an error code even with the cooked MPU. So it was booting up to a point.  You can always try putting the old one back in just to see if it still gives you an error.
Logged
shortrackskater
NLG Site Administrator
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 192
Offline Offline

Gender: Male
Posts: 845


Insert Coin
« Reply #59 on: August 17, 2011, 07:41:10 PM »
Okay...I'll try...also one thing - the transformer on the MPU case does smell although there's no physical evidence of it being burned...but could I have fried that? I hope that, most likely it's just residual smell from the resistor pack.
Logged
poppo
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 248
Offline Offline

Gender: Male
Posts: 3266
« Reply #60 on: August 17, 2011, 07:44:04 PM »
See my edit above about how it was booting to a point before. So your MPU transformer is probably good.
Logged
shortrackskater
NLG Site Administrator
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 192
Offline Offline

Gender: Male
Posts: 845


Insert Coin
« Reply #61 on: August 17, 2011, 07:59:10 PM »
Jumpers were all okay and yes, I did unplug that 9 pin already...just in case. Do you know what U 54 does? Should I put the one in from the old board? This was a tested and working board, according to the seller...he's on this site so I'm sure he's highly reliable!

I'm going to try sticking the old board back in and see if I get the error code.
« Last Edit: August 17, 2011, 08:15:36 PM by shortrackskater » Logged
poppo
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 248
Offline Offline

Gender: Male
Posts: 3266
« Reply #62 on: August 17, 2011, 08:14:56 PM »
Quote from: shortrackskater on August 17, 2011, 07:59:10 PM
Jumpers were all okay and yes, I did unplug that 9 pin already...just in case. Do you know what U 54 does? Should I put the one in from the old board? This was a tested and working board, according to the seller...he's on this site so I'm sure he's highly reliable!

U54 is the CPU.

I would try putting your old board back in first to see if you can get at least an error or some display to come up. That will help to determine if you have other problems, or if the new MPU has issues.  
Logged
shortrackskater
NLG Site Administrator
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 192
Offline Offline

Gender: Male
Posts: 845


Insert Coin
« Reply #63 on: August 17, 2011, 08:21:44 PM »
Old board in. I get error code b1 and the top candle lights start to flash - it's the CHANGE candle and button that light up and flash.
Logged
poppo
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 248
Offline Offline

Gender: Male
Posts: 3266
« Reply #64 on: August 17, 2011, 08:27:06 PM »
Quote from: shortrackskater on August 17, 2011, 08:21:44 PM
Old board in. I get error code b1 and the top candle lights start to flash - it's the CHANGE candle and button that light up and flash.

b1 or 61? 61 is normal any time you fiddle with the CMOS. In any case you are getting something. I hate to say it, but I think you got a bad replacement MPU.

But you can try swapping ALL of the socketed chips again and see what happens.
Logged
shortrackskater
NLG Site Administrator
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 192
Offline Offline

Gender: Male
Posts: 845


Insert Coin
« Reply #65 on: August 17, 2011, 08:30:24 PM »
I think that is a 6...if the top segment was lite, I would have called it a G !
Logged
poppo
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 248
Offline Offline

Gender: Male
Posts: 3266
« Reply #66 on: August 17, 2011, 08:33:57 PM »
Quote from: shortrackskater on August 17, 2011, 08:30:24 PM
I think that is a 6...if the top segment was lite, I would have called it a G !


There are no letter codes, that is why I asked. If you still have the old board in, you should be able to press the self test and have it change to a 61_1 If it does that, I would not go any farther since you know you will get other errors. But it shows the machine is booting. If the replcement MPU is not at least giving you a 61, I think its bad.
Logged
shortrackskater
NLG Site Administrator
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 192
Offline Offline

Gender: Male
Posts: 845


Insert Coin
« Reply #67 on: August 17, 2011, 08:36:01 PM »
...and I promise I'm not drinking wine! Okay...so I will put back in the new board, with chips and I'll be back...
Logged
knagl
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 642
Offline Offline

Gender: Male
Posts: 5489


Kevin
« Reply #68 on: August 17, 2011, 08:36:39 PM »
I can see how a S+ n00b would call it "b1":


(Image credit: Stolistic)

(No offense intended at all with the term "n00b" -- I was one not that long ago, too!)
Logged
If you find this site helpful, please consider making a small donation to help defray the cost of hosting and bandwidth.

Please do not PM me for support or "how to" requests -- please post your request in the forum so that everyone may assist you and everyone can benefit from the answer to your question!  Thanks! Smiley
shortrackskater
NLG Site Administrator
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 192
Offline Offline

Gender: Male
Posts: 845


Insert Coin
« Reply #69 on: August 17, 2011, 08:46:27 PM »
No offense whatsoever! I'm VERY happy to be here...new or not! I've never seen a group of people as helpful - anywhere.
As a side note anyone know what happened to Emelie? That was a very fun and informative thread going on.

One chip I didn't swap out was U54. Should I? Maybe it's the culprit?
Logged
poppo
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 248
Offline Offline

Gender: Male
Posts: 3266
« Reply #70 on: August 17, 2011, 08:48:56 PM »
Quote from: shortrackskater on August 17, 2011, 08:46:27 PM
One chip I didn't swap out was U54. Should I? Maybe it's the culprit?

Can't hurt at this point. You know your old one is good.
Logged
shortrackskater
NLG Site Administrator
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 192
Offline Offline

Gender: Male
Posts: 845


Insert Coin
« Reply #71 on: August 17, 2011, 08:54:00 PM »
Nothing...no code. Last chip I just realized I didn't swap out is U49. What does that one do? I'll just try it...
Logged
poppo
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 248
Offline Offline

Gender: Male
Posts: 3266
« Reply #72 on: August 17, 2011, 08:55:39 PM »
Quote from: shortrackskater on August 17, 2011, 08:54:00 PM
Nothing...no code. Last chip I just realized I didn't swap out is U49. What does that one do? I'll just try it...

Sound chip. Probably not going to help.
Logged
shortrackskater
NLG Site Administrator
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 192
Offline Offline

Gender: Male
Posts: 845


Insert Coin
« Reply #73 on: August 17, 2011, 08:57:32 PM »
I'm glad you people know what you're doing. I'd be totally lost.
Okay, nothing happened...no code.
"It's dead Jim"
Should I contact the seller at this point?
Logged
poppo
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 248
Offline Offline

Gender: Male
Posts: 3266
« Reply #74 on: August 17, 2011, 09:02:12 PM »
Quote from: shortrackskater on August 17, 2011, 08:57:32 PM
Should I contact the seller at this point?

I would. I think we have pretty much determined that there is something wrong with it.

I would just check those two grey connectors on the bottom of the MPU one more time to make sure there are no bent pins. I know you already did, but I had one that would not boot and it turned out there was one pin bent causing the MPU not to seat all of the way.
Logged
Pages: 1 2 [3] 4 Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.102 seconds with 21 queries.