Welcome, Guest. Please login or register.
June 16, 2024, 06:31:30 AM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  Bally Reel Games. (Moderator: a69mopar)
| | |-+  Correct sound chip?
0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Correct sound chip?  (Read 3419 times)
Red7
NLG Member 101 to 500 Post
***

Total Karma Storms: 14
Offline Offline

Gender: Male
Posts: 124


I love my slots.....


« on: September 06, 2012, 07:08:20 PM »

Hey there,

Does anyone know the proper sound chip for this machine? and where I can get one? It has one in it now.. although it will not play any sounds when you hit spin-spin-2x, or spin-spin-3x.. but if you hit spin-spin-spin, and spin-spin-double pay.. then it has the correct audio playing..

thanks

Steve



* IMG-20120906-00667.jpg (149.97 KB, 486x648 - viewed 278 times.)
« Last Edit: September 07, 2012, 08:54:40 PM by a69mopar » Logged
blueridgeslots
703 730-0821
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1262
Offline Offline

Gender: Male
Posts: 1779


703 730-0821


WWW
« Reply #1 on: September 06, 2012, 08:44:22 PM »

Try straightening the pin near the 03 on the label at the edge opposite pin 1 (the small dot) if not we may have another one for it
Logged

Selling Quality Tested and Guaranteed Slot Parts and Machines at Wholesale

http://stores.ebay.com/BLUE-RIDGE-SLOT-SERVICE
Red7
NLG Member 101 to 500 Post
***

Total Karma Storms: 14
Offline Offline

Gender: Male
Posts: 124


I love my slots.....


« Reply #2 on: September 07, 2012, 12:14:21 AM »

Hey thanks.. I will have a look in the morning.. I didn't see the bent pin today.. You have a good eye.. I will let you know if that was the issue.. Does anyone know if the code on the chip actually go to this game?

thanks

Steve
Logged
Red7
NLG Member 101 to 500 Post
***

Total Karma Storms: 14
Offline Offline

Gender: Male
Posts: 124


I love my slots.....


« Reply #3 on: September 07, 2012, 11:58:11 AM »

Well I did give it a shot.. I took the chip out and tried to straighten that pin.. Being my first time working with this kind of chip.. it was a bit of a mess I should say.. The pin has left the chip forever.. and the machine no longer has any voice of it's own.. Sad

If anyone has a chip please let me know..

Thanks

(I don't know if it even was the right chip to start with.. possibly could have been if the bent pin was stopping it from operating properly?  I will never know.. )

Steve

Logged
a69mopar
647-402-1977
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 600
Offline Offline

Gender: Male
Posts: 3508



WWW
« Reply #4 on: September 07, 2012, 08:47:45 PM »

Hi Steve,
  I have one, email me...  The bent pin would have it to not work at all, not the incorrect sounds.  

Thanks,
Wayne
« Last Edit: September 07, 2012, 08:55:37 PM by a69mopar » Logged

         www.GTASLOTS.com      647-402-1977              BALLY S6000 GALLERY
tucsondirect
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Gender: Male
Posts: 30



« Reply #5 on: October 23, 2012, 09:13:31 PM »

Well I did give it a shot.. I took the chip out and tried to straighten that pin.. Being my first time working with this kind of chip.. it was a bit of a mess I should say.. The pin has left the chip forever.. and the machine no longer has any voice of it's own.. Sad

If anyone has a chip please let me know..

Thanks

(I don't know if it even was the right chip to start with.. possibly could have been if the bent pin was stopping it from operating properly?  I will never know.. )

Steve


the pin CAN be soldered back on if you tin the post first then glob some solder, let it cool and carefully stack or even tape the broken pin or a peice of metal near the same size on top of it. Then apply the iron to the bottom side of the pin, just until it melts into place.
Remove the iron in a quick jerk while staying parallel to the pin
Logged
a69mopar
647-402-1977
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 600
Offline Offline

Gender: Male
Posts: 3508



WWW
« Reply #6 on: October 24, 2012, 12:52:28 PM »

the pin CAN be soldered back on if you tin the post first then glob some solder, let it cool and carefully stack or even tape the broken pin or a peice of metal near the same size on top of it. Then apply the iron to the bottom side of the pin, just until it melts into place.
Remove the iron in a quick jerk while staying parallel to the pin
I'm not saying that it can't be done, but this is not a DIP chip, it is a TSOP48.  The pins are very fine, and the heat can affect the chip if you're not careful.


* tsop48 compared to dip28.jpg (1394.18 KB, 2328x1271 - viewed 301 times.)
Logged

         www.GTASLOTS.com      647-402-1977              BALLY S6000 GALLERY
tucsondirect
New NLG Member 1 to 100 Post
**

Total Karma Storms: 0
Offline Offline

Gender: Male
Posts: 30



« Reply #7 on: October 24, 2012, 02:32:59 PM »

the pin CAN be soldered back on if you tin the post first then glob some solder, let it cool and carefully stack or even tape the broken pin or a peice of metal near the same size on top of it. Then apply the iron to the bottom side of the pin, just until it melts into place.
Remove the iron in a quick jerk while staying parallel to the pin
I'm not saying that it can't be done, but this is not a DIP chip, it is a TSOP48.  The pins are very fine, and the heat can affect the chip if you're not careful.
oops
thought it was a Dip,

Your best bet would be to solder a jumper wire to it
or radios shack sells conductive glue goop stuff that is great for these little problems
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  


If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com    Newlifegames.net    Newlifegames.org
   New Life Games    NewLifeGames  NLG  We Bring new Life to old Games    1-888-NLG-SLOTS
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.141 seconds with 20 queries.