Welcome, Guest. Please login or register.
November 22, 2024, 03:47:17 AM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  Bally Reel Games. (Moderator: a69mopar)
| | |-+  Bally E1202 with startup error code 7 (repost?)		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: Bally E1202 with startup error code 7 (repost?)  (Read 3681 times)
deanwaters
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 11
Offline Offline

Posts: 21
« on: February 01, 2014, 05:41:19 AM »
Hey everyone.  I have a Bally E-1202 that I bought from foxslots many years ago.  It's been a great machine and now it needs some love.  It hadn't been powered for many months and when I fired it up recently, I got a "50 000" on the screen.  The Test/Reset buttons didn't do any good.  Opening and closing the door didn't help either.  I pulled the daughter-board with the battery just to the left of the reel assembly and re-seated it.  NOW when I power up the machine, I get a "7" in the first LED position.  Hope I didn't make a bad problem worse!  Pictures attached.  I have 4 Bally's in my collection.  3 of which I got from foxslots.  They are all great.  This is my only E series.  The rest are older.  Ideas?
Dean

* Error code 50 000.JPG (131.06 KB, 1332x649 - viewed 388 times.)

* Error code 7.JPG (115.82 KB, 1321x586 - viewed 411 times.)
Logged
dhellis
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 56
Offline Offline

Gender: Male
Posts: 172
« Reply #1 on: February 01, 2014, 05:47:17 AM »
Take the ram board back off and then take a wire brush to the pins to clean them off real good. If you know how to solder
then flip the MPU board over and allow the solder to flow on each of the pins for the ram board, be careful not to create
a short while doing this.

Let us know how that works out.
Logged
deanwaters
Contributing NLG Member
New NLG Member 1 to 100 Post
*

Total Karma Storms: 11
Offline Offline

Posts: 21
« Reply #2 on: February 02, 2014, 04:03:04 AM »
Well I think I've made a bit of progress.  I pulled the boards, cleaned the contacts as best I could and reseated them.  The Error "7" is gone.  Now I get an error "50  . .00" (see pic).  The candle goes on and off when I open and close the door and the Tilt light is now lit.  The Reset & Test buttons don't seem to do anything.  I hope I'm moving in the right direction.  Not sure what to do next.

Dean

* Error 50.JPG (131.4 KB, 1316x700 - viewed 409 times.)
Logged
proten
Contributing Gold NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 210
Offline Offline

Gender: Male
Posts: 1130
« Reply #3 on: February 02, 2014, 04:21:31 AM »
Code 50 is the door open code.
Until you get the test and reset
buttons to work you will no get any farther.
Do you have a manual for your machine?
Logged
One step at a time.
dhellis
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 56
Offline Offline

Gender: Male
Posts: 172
« Reply #4 on: February 02, 2014, 04:29:22 AM »
That is close, you should have 50 0000 once the door is open, you have 50 ..00 so maybe a tad more elbow grease on the pins for the ram board.
Did you resolder the connecting pins on the bottom of the board? these will get small cracks in the solder and cause bad connections. Until you
get a 50 000 you won't be able to run any further tests, but then you may not have to either.
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.096 seconds with 20 queries.