Welcome, Guest. Please login or register.
October 31, 2024, 09:06:24 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  Bill Validators and Currency acceptors
| |-+  JCM DBV-45, DBV-145, and DBV-200 Bill Validators.
| | |-+  DBV-145 bills go in and then back out (Fixed)		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: DBV-145 bills go in and then back out (Fixed)  (Read 12359 times)
SK8US
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 198
« on: January 16, 2010, 10:21:39 PM »
Hi,
I have a Bally 5500 Fireball slot with the DBV 145 bill validator in it. The machine plays great but the will not accept bills. This slot is new to me so I don't know when it has stopped working?
When it is on and ready to play the bill acceptor's green light is on and it will feed into the acceptor but spits them out. The dip switch on the bottom of the acceptor head are all off except the last one in the first switch bank and the two are on, on the other switch bank.
Any Ideas?

Thanks again for all your help.............
« Last Edit: January 23, 2010, 11:29:16 PM by SK8US » Logged
SK8US
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 198
« Reply #1 on: January 17, 2010, 01:20:14 AM »
I found a great site for Dip Switch settings on most acceptors http://www.myslotnotes.com/DBA%20DIP%20SWITCH%20SETTINGS.htm  My acceptor is set correct and still doesn't accept bills.
Logged
sfrench
Guest
« Reply #2 on: January 18, 2010, 01:12:10 PM »
have you calibrated the bv yet? this is a manual calibration
Logged
SK8US
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 198
« Reply #3 on: January 18, 2010, 02:28:10 PM »
No I have not done the calibration. Could you explain how to? This is on a Bally 5500 with a DBV 145.
Thanks,
 Scott
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #4 on: January 18, 2010, 03:03:52 PM »
Scott,
Check out this was a great thread on DBV-145's.>>>

http://newlifegames.net/nlg/index.php?topic=4677.0


JCM stopped putting up information on the 145's some time back
and the calibration procedures were very complicated I understand.
Plus the bloody things were never updated so nearly everyone
I know went to the 200 head's and got the stronger power supply
with the vents to power it up.
I seriously think you should take this route because there's a
lot more documentation available for the 200 heads!
I'd place an ad for in the NLG "Classifieds" section and I'm sure
one of our esteemed will be glad to help you out!
Logged
SK8US
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 198
« Reply #5 on: January 18, 2010, 03:20:54 PM »
Thanks, I'll check it out. I do have a 200 head and I think I found a power supply for it. I'll get back if it works.
Scott
Logged
SK8US
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 198
« Reply #6 on: January 18, 2010, 03:52:36 PM »
Hi, this may sound stupid but I cant find the power supply for the 145 to replace with the new supply. It appears that the wiring harness from the BV goes to the back board on this Bally 5500. Am I looking in the wrong place? I am looking inside the slot machine............ I'll look more............ Will the new power supply for the 200 need adaptors?
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #7 on: January 18, 2010, 03:58:06 PM »
NO! You're right!
I looked at mine...
The DBV on a Bally5500 gets its power from the machines' main power supply box!
Thanks for making me go check on that!
When you place your ad in the Classifieds section...
make sure you say that your wanting a 200 DBV head w/harness for the Bally5500 machine!
Logged
SK8US
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 198
« Reply #8 on: January 18, 2010, 04:12:07 PM »
I have a 200 head but will it work without the new power supply? Or can I just plug it in with the existing wires? Could I try or not?
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #9 on: January 18, 2010, 04:28:10 PM »
I'd read some threads on the DBV-145 forum area first!
your DBV software has to match a Bally5500...
Some are made for IGT's, Aristocrats, Williams,etc.etc.
« Last Edit: January 18, 2010, 04:33:57 PM by stayouttadabunker » Logged
SK8US
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 198
« Reply #10 on: January 18, 2010, 04:37:22 PM »
Sounds good as this 200 head is off a IGT transport.
Logged
sfrench
Guest
« Reply #11 on: January 18, 2010, 05:03:21 PM »
its not really that bad to calibrate the 145 we nolonger use the 145 how every we still use the DBV-147 in our old IGT mutiGames same calibration some what except you need to use the jcm test box to flip the switch to see the other wave forms. i would put a DBV 200 in place of the 145 much easier to repair and it has the auto calibration no more pain in the a$! pots to turn. just a few dipswitches.
Logged
SK8US
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 198
« Reply #12 on: January 18, 2010, 05:20:28 PM »
So I can just exchange the 145 with a 200 head on my Bally 5500 without a new power supply and using the same harness?
Thanks,
 Scott
Logged
SK8US
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 198
« Reply #13 on: January 18, 2010, 05:22:30 PM »
Also is there a thread or manual on calibrating the 200?
« Last Edit: January 18, 2010, 05:41:14 PM by SK8US » Logged
StatFreak
rotaredoM etiS GLN labolG
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 756
Offline Offline

Gender: Male
Posts: 8549


Warning! Spammers will be eaten, with relish!
« Reply #14 on: January 19, 2010, 03:59:30 AM »
Quote from: SK8US on January 18, 2010, 05:20:28 PM
So I can just exchange the 145 with a 200 head on my Bally 5500 without a new power supply and using the same harness?
Thanks,
 Scott

Yes, as long as the head is a DBV 200 SH, protocol 044/045
Logged
I found myself at NLG garfield  ..but got lost again on the way home. Scratch Head 2
If found, please email me to myself. Thanks. yes
       Executive member in good standing of Rick's SMAA.                              Ehhh...What's Up Doc?
StatFreak
rotaredoM etiS GLN labolG
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 756
Offline Offline

Gender: Male
Posts: 8549


Warning! Spammers will be eaten, with relish!
« Reply #15 on: January 19, 2010, 04:02:19 AM »
Quote from: SK8US on January 18, 2010, 05:22:30 PM
Also is there a thread or manual on calibrating the 200?

You need a special paper to calibrate the dbv200. The calibration sheet is half black and half white. One side is plain paper and the other is special (I believe that the black is special, but I suffer from CRS). You should be able to buy some from one of our vendors.
Logged
I found myself at NLG garfield  ..but got lost again on the way home. Scratch Head 2
If found, please email me to myself. Thanks. yes
       Executive member in good standing of Rick's SMAA.                              Ehhh...What's Up Doc?
SK8US
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 198
« Reply #16 on: January 19, 2010, 04:19:11 AM »
where would I find the protocol numbers? Thanks, Scott
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #17 on: January 19, 2010, 04:25:39 AM »
It's in your other thread...a69mopar gave you the answer...
you have two threads on this?
I'm all mixed up now...

http://newlifegames.net/nlg/index.php?topic=6106.msg54595;topicseen#new
Logged
SK8US
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 198
« Reply #18 on: January 19, 2010, 04:50:05 AM »
I know""""""!! I didnt get any post for awhile so I tried the other board. I should join them??
Logged
SK8US
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 198
« Reply #19 on: January 23, 2010, 11:29:40 PM »
What I did was put in a new DBV and it didnt work then I changed my MPU board and my old DBV and now it works. Thanks for all your help............
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #20 on: January 24, 2010, 01:21:22 AM »
Quote from: SK8US on January 23, 2010, 11:29:40 PM
What I did was put in a new DBV and it didnt work then I changed my MPU board and my old DBV and now it works. Thanks for all your help............

Hey! It's working!!! Yea!! The Wave Ecstatic / Top Award
Logged
SK8US
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 6
Offline Offline

Gender: Male
Posts: 198
« Reply #21 on: January 24, 2010, 02:03:26 AM »
Hay, Thanks for your help again. If I was going to keep this for a long time I would switch to a 200 head.... Have A Great Weekend...........
Logged
Pages: [1] Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.095 seconds with 19 queries.