Welcome, Guest. Please login or register.
November 22, 2024, 07:35:11 PM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  **Reel Slots** Gaming Machines
| |-+  Bally Reel Games. (Moderator: a69mopar)
| | |-+  BALLY 5000+ Coin Acceptance Issue
0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] Go Down Print
Author Topic: BALLY 5000+ Coin Acceptance Issue  (Read 5254 times)
coinopshop
NLG Member 101 to 500 Post
***

Total Karma Storms: 3
Offline Offline

Posts: 123



« on: March 24, 2010, 12:39:32 PM »

 Ok. These things are REALLY starting to drive me nuts ! I have 3 Coin Comparitors ALL are CC-62-D. I have one 5000+ slot which takes coins fine. I tried ALL 3 of these extra coin units in my working machine and THEY ALL WORKED ( so I know they are good ). BUT.....when I put any of them in my other 5000+ the machine will not accept any coins with any installed mech.

 I did notice on my working machine, the "INSERT COIN" light is lit. On the other machine which I am trying to get to accept coins, the "INSERT COIN" light does not light at all ( and yes, I changed the bulbs ). I also can't seem to do a clear on this other machine ( pcb dated 1989 ) either with the Psudo button or clear chips.

 If I phyically hold the coin acceptor solenoid lever out while in game over, the machine will recognise a coin and start play. EXTREMELY strange. I need your expert advice.

 Thanks,
 Dave.
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447



« Reply #1 on: March 24, 2010, 01:06:47 PM »

Follow that wire>>>coin acceptor solenoid lever <<<  from the solenoid to wherever.
Make sure it's not broken or pinched anywhere.
Logged
rjpohl
Contributing Gold NLG Member
Sr.NLG Member 501 to 1000 Post
*

Total Karma Storms: 103
Offline Offline

Gender: Male
Posts: 726



WWW
« Reply #2 on: March 24, 2010, 01:17:29 PM »

I believe there is a toggle switch on the front of the CPU board marked "coin-in" (may be exact)  pretty sure this switch controls whether it will or will not accept coins.  Check the way the toggle is set on the working machine, then make sure it's that way on the other machine.  Good luck

Bob
Logged

coinopshop
NLG Member 101 to 500 Post
***

Total Karma Storms: 3
Offline Offline

Posts: 123



« Reply #3 on: March 24, 2010, 01:38:52 PM »

 Again, all 3 of these mechs WORK in another machine of mine. No broken wires.

Follow that wire>>>coin acceptor solenoid lever <<<  from the solenoid to wherever.
Make sure it's not broken or pinched anywhere.
Logged
coinopshop
NLG Member 101 to 500 Post
***

Total Karma Storms: 3
Offline Offline

Posts: 123



« Reply #4 on: March 24, 2010, 01:41:22 PM »

 On the coin-psudo pcb there is a switch with 2 positions on it. ENABLE and DISABLE. Both machines are set to ENABLE.  THere are quite a few jumpers on the 5000+ MPU, but I have no idea what they do as they are not marked.
Logged
a69mopar
647-402-1977
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 600
Offline Offline

Gender: Male
Posts: 3508



WWW
« Reply #5 on: March 24, 2010, 08:20:45 PM »

Check to make sure the door switch is working.  It wont accept coins if it thinks the door is open.

Thanks,
Wayne
Logged

         www.GTASLOTS.com      647-402-1977              BALLY S6000 GALLERY
coinopshop
NLG Member 101 to 500 Post
***

Total Karma Storms: 3
Offline Offline

Posts: 123



« Reply #6 on: March 24, 2010, 08:30:38 PM »

 Yeap. Did that also. I held the door switch in with my finger then tried to insert a coin.

 No go.


Check to make sure the door switch is working.  It wont accept coins if it thinks the door is open.

Thanks,
Wayne
Logged
Goldfinger
Contributing NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 31
Offline Offline

Gender: Male
Posts: 294



« Reply #7 on: June 03, 2010, 03:53:24 PM »

Did you ever get this machine to work? if so what was the fix?
Goldfinger
Logged

If it's to big to fit, just get a bigger hammer
coinopshop
NLG Member 101 to 500 Post
***

Total Karma Storms: 3
Offline Offline

Posts: 123



« Reply #8 on: June 05, 2010, 12:08:24 PM »

YES and NO.

 Answer NO: I did not figure out why the machine would not accept any coins -or- light the "Insert Coin" bulb in a "NORMAL" operating mode.

 Answer YES: Not so correct solution was to tie pins 1&2 together at J4 of the Psudo Coin pcb located on the front door. **BEWARE ! ** If you switch the coin enable switch to disable you will fry the trace from pin 1 of J4. Trust me, I did it !

 This allows coins to be accepted BUT ( BUT ).....you can put more than the 3 coins maximum in the machine which may/can cause a coin error. BUT IT DOES WORK ! Even if it's not the correct way to do it.

 Dave.
Logged
ROCKET
ROCKET
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 430
Offline Offline

Gender: Male
Posts: 1278


I DONT SELL ON EBAY ITS NOT ME .


« Reply #9 on: June 05, 2010, 12:30:29 PM »

REMOVED
« Last Edit: June 12, 2010, 11:42:56 AM by ROCKET » Logged

The content of your character is your choice. Day by day, WHAT YOU CHOOSE TO POST , what you think & what you do is who you become.
coinopshop
NLG Member 101 to 500 Post
***

Total Karma Storms: 3
Offline Offline

Posts: 123



« Reply #10 on: June 05, 2010, 01:14:59 PM »

FYI  -- I have had alot of experience with the 62-d comp.
its used in bally's

but also used in UNIDESA slots made in spain
the 62-D---- some are a universal comp. which will accept a nickel to a 1.00 token -- yes you read that correct ..

 Yepper. That's exactly what these coin units are. I've adjusted these already but it still wouldn't take a coin in this particular machine ( read above posts where I mention trying it in another machine and worked. )

I have now?? -- about  --30 -plus of them in stock -new and used .

if you flip it upside down you can adjust it to take the SAMPLE SIZE COIN YOU INTEND TO USE ---"THERE IS A MINI RULER ON THEM " if its not set correct it will give crazy readings in a UNIDESA AND A BALLY !!

it took me about 15 minutes of trial and error to adjust the slide in the back to get the sample token/coin to work .
once you have one and see it you will pick up quick what I am saying  !! if not a picture is worth a thousand words !!


Logged
ROCKET
ROCKET
Contributing NLG Member
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 430
Offline Offline

Gender: Male
Posts: 1278


I DONT SELL ON EBAY ITS NOT ME .


« Reply #11 on: June 05, 2010, 01:27:50 PM »

REMOVED
« Last Edit: June 12, 2010, 11:42:14 AM by ROCKET » Logged

The content of your character is your choice. Day by day, WHAT YOU CHOOSE TO POST , what you think & what you do is who you become.
Pages: [1] Go Up Print 
« previous next »
Jump to:  


If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com    Newlifegames.net    Newlifegames.org
   New Life Games    NewLifeGames  NLG  We Bring new Life to old Games    1-888-NLG-SLOTS
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.133 seconds with 20 queries.