Welcome, Guest. Please login or register.
November 22, 2024, 03:48:37 AM

Login with username, password and session length
* Home Help Arcade Login Register
.
+  Forum
|-+  Progressive Controllers, Displays and Slot Toppers
| |-+  Mikohn Progressive Systems.
| | |-+  Help getting started with a Mikohn Supreme setup...		 0 Members and 1 Guest are viewing this topic. « previous next »
Pages: [1] 2 3 4 5 Go Down Print
Author Topic: Help getting started with a Mikohn Supreme setup...  (Read 74895 times)
knagl
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 642
Offline Offline

Gender: Male
Posts: 5489


Kevin
« on: October 24, 2009, 09:11:48 PM »
Greetings, all.

A friend of mine bought a bunch of machines that had a Mikohn "MoneyTime" linked progressive when they were in the casinos (discussed previously, here).  Each machine had a Supreme inside of it, with a 12-cell by 2-cell display.  Here is the whole setup that we pulled from one of the machines:


(Click on the photo for a bigger image)

From my limited Mikohn knowledge, the "extra" square board pictured between the main Supreme board and the display isn't needed, right?  (I'm assuming it had something to do with the MoneyTime link.)

Also, there is no U3 chip on either board (the square board or the main board).  Am I correct that the 40-pin chip that goes into U3 on the main board contains the main software for the controller?  Right now when plugged in, we get a couple of LEDs on the main board, and the display board has one red LED on the back that seems to indicate it's getting power.  Nothing shows up on the display, which I'm hoping is because we're missing U3 chip.

Does anyone know what kind/size chip that U3 is, and can confirm that I really do need that to do anything with this?

Also, once I have that chip, how do I communicate with the controller to program anything in them?  (We'd like to program text and/or graphics -- no need for progressive functions, though.)

Thanks in advance!
Logged
If you find this site helpful, please consider making a small donation to help defray the cost of hosting and bandwidth.

Please do not PM me for support or "how to" requests -- please post your request in the forum so that everyone may assist you and everyone can benefit from the answer to your question!  Thanks! Smiley
jay
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 483
Offline Offline

Gender: Male
Posts: 3178


if you cant afford to lose you cant afford to win
« Reply #1 on: October 24, 2009, 09:16:24 PM »
You would use the MIKOHN downloader software..... and a PC with a serial cable to feed the supreme controller.
This will get you text and graphics but no progressive function. For that you would need the CON2.
Logged
The only way to beat the casino is to own it
StatFreak
rotaredoM etiS GLN labolG
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 756
Offline Offline

Gender: Male
Posts: 8549


Warning! Spammers will be eaten, with relish!
« Reply #2 on: October 25, 2009, 01:55:25 AM »
Jay, what is needed in U3?
Logged
I found myself at NLG garfield  ..but got lost again on the way home. Scratch Head 2
If found, please email me to myself. Thanks. yes
       Executive member in good standing of Rick's SMAA.                              Ehhh...What's Up Doc?
brichter
Spaced Alien
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 440
Offline Offline

Gender: Male
Posts: 2374



WWW
« Reply #3 on: October 25, 2009, 02:57:20 AM »
That's the actual software that drives the display.

<edit>

Here's a picture for clarity:

* IMG_9687_resize.JPG (282.92 KB, 1024x682 - viewed 827 times.)
Logged
Thanks,
Bill
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #4 on: October 25, 2009, 03:00:59 AM »
Mikohn Logic Board;

Problem; Display Blackout.
Solution; Repl. U8

Problem; Blackout.
Solution; Repl. U9 (HA1835).

Problem; Display zizzing & dripping (flipping from C3 to lines or solid lights)
Solution; Repl. U3 (RAM).

40-pin Random Access Memory chip?

ADD>>> oh, okay...a CSM/V2.10 U3 cs 1883 chip...readily available?
« Last Edit: October 25, 2009, 03:14:42 AM by stayouttadabunker » Logged
brichter
Spaced Alien
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 440
Offline Offline

Gender: Male
Posts: 2374



WWW
« Reply #5 on: October 25, 2009, 03:15:54 AM »
It will not function without the software. I imagine the functionality would be different if the chip was there and defective...

Here's a screenshot of the hardware diagram from the manual showing U3 as an EPROM, and the RAM as U5 and U6:

* CShw.JPG (93.8 KB, 1117x738 - viewed 892 times.)
« Last Edit: October 25, 2009, 05:00:13 AM by brichter » Logged
Thanks,
Bill
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #6 on: October 25, 2009, 03:20:06 AM »
Looks like a AM27C4006 AM27C4096    40-pin device.

ADMIN NOTE: Changed Part Number Above. CH CaptainHappy
« Last Edit: October 25, 2009, 04:37:45 AM by CaptainHappy » Logged
CaptainHappy
NLG Site Administrator
NLG Site Administrator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 622
Offline Offline

Gender: Male
Posts: 3203


I haven't met a Jackpot that I didn't like!!!
« Reply #7 on: October 25, 2009, 04:34:06 AM »
Quote from: stayouttadabunker on October 25, 2009, 03:20:06 AM
Looks like a AM27C4006 AM27C4096 40-pin device.

Bunker, Zooming Sherlock Smiley did not work for you this time!  bust gut laughing  In your defense, it was hard to zoom clearly as I wanted to check if my numbers I wrote down were wrong after seeing your post!

I wrote this information down from my supreme earlier and forgot to post it...

CSM/V2.10
(c)96 Mikohn
U3 cs 1883

The device is actually a M27C4096-120DC (Same as M27C4002 This is the Base Chip used by IGT for S2000 SB... and GameKing I... or M... Base Chips.) It is a 16 BIT 40 Pin Eprom, and most programmers require an adapter to read and program them.

I am sure that these Mikohn CHIPS are readily available if you need to find them.  yes yes yes

CaptainHappy CaptainHappy
Logged
  Come sail away, Come sail away Come sail away with me..
brichter
Spaced Alien
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 440
Offline Offline

Gender: Male
Posts: 2374



WWW
« Reply #8 on: October 25, 2009, 05:03:43 AM »
Adapter? It's a DIP package, so should be supported by most burners. I guess if you have less than 40 pins on the original socket, an adapter may be necessary.

It is indeed a 27C4096/4002. Sorry the original pic was not big enough to read the P/N, I didn't check. After I posted, I couldn't read it either!  Duh! Cry Laughing

I made it a little bigger for us old pharts. rotflmao
Logged
Thanks,
Bill
CaptainHappy
NLG Site Administrator
NLG Site Administrator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 622
Offline Offline

Gender: Male
Posts: 3203


I haven't met a Jackpot that I didn't like!!!
« Reply #9 on: October 25, 2009, 05:27:24 AM »
Quote from: brichter on October 25, 2009, 05:03:43 AM
Adapter? It's a DIP package, so should be supported by most burners. I guess if you have less than 40 pins on the original socket, an adapter may be necessary.

It is indeed a 27C4096/4002. Sorry the original pic was not big enough to read the P/N, I didn't check. After I posted, I couldn't read it either!  Duh! Cry Laughing

I made it a little bigger for us old pharts. rotflmao

Bill,

The reason that I mention adapter is that it depends on your programmer. The issue is not the 40 pin issue, but more that these eproms are 16BIT vs the normal 8BIT eproms. Most of the hobbyist programmers do not burn the 16BITt chips without a adapter like a daughter card. If you have a pricier programmer then it probably works out of the gate! I use the GQ4X which is decent, but I have to use an adapter for these style chips.

Mark CaptainHappy
Logged
  Come sail away, Come sail away Come sail away with me..
brichter
Spaced Alien
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 440
Offline Offline

Gender: Male
Posts: 2374



WWW
« Reply #10 on: October 25, 2009, 05:34:44 AM »
Ahh, ok, that makes sense. Mine does those natively, but it cost $$, even though it was an open box special from (French) Fries.
Logged
Thanks,
Bill
knagl
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 642
Offline Offline

Gender: Male
Posts: 5489


Kevin
« Reply #11 on: October 25, 2009, 08:56:52 AM »
K+ to all and thanks for the info -- this puts us on the right track.   applause
Logged
If you find this site helpful, please consider making a small donation to help defray the cost of hosting and bandwidth.

Please do not PM me for support or "how to" requests -- please post your request in the forum so that everyone may assist you and everyone can benefit from the answer to your question!  Thanks! Smiley
kenokarz
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 284
Offline Offline

Gender: Male
Posts: 470
« Reply #12 on: October 25, 2009, 12:29:13 PM »
will it work on a chipmax without the adapter ??? mine will take the 40 pin chip
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #13 on: October 25, 2009, 01:00:32 PM »
Quote from: kenokarz on October 25, 2009, 12:29:13 PM
will it work on a chipmax without the adapter ??? mine will take the 40 pin chip

If your Chipmax takes 40-pins,  it should!

but these chips are 41-pins...



(just kidding ya keno... Tongue Out)

hey ch, thank you for the chip correction!
(...man, I think I need glasses now.)
Logged
brichter
Spaced Alien
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 440
Offline Offline

Gender: Male
Posts: 2374



WWW
« Reply #14 on: October 25, 2009, 04:19:37 PM »
Quote from: kenokarz on October 25, 2009, 12:29:13 PM
will it work on a chipmax without the adapter ??? mine will take the 40 pin chip

The below is from Chipmax software v3.1k. Looks like you're good to go:

* 4096-chipmax.JPG (44.68 KB, 787x842 - viewed 759 times.)
Logged
Thanks,
Bill
CaptainHappy
NLG Site Administrator
NLG Site Administrator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 622
Offline Offline

Gender: Male
Posts: 3203


I haven't met a Jackpot that I didn't like!!!
« Reply #15 on: October 25, 2009, 06:24:40 PM »
Quote from: brichter on October 25, 2009, 04:19:37 PM
Quote from: kenokarz on October 25, 2009, 12:29:13 PM
will it work on a chipmax without the adapter ??? mine will take the 40 pin chip

The below is from Chipmax software v3.1k. Looks like you're good to go:

Bill,

Now that picture was really big!  Cry Laughing Cry Laughing Cry Laughing

Kenokarz,

You should be fine as that is the same chip for S2000, GK, IG+ Key and Base chips that you probably backup.

CH CaptainHappy
Logged
  Come sail away, Come sail away Come sail away with me..
CaptainHappy
NLG Site Administrator
NLG Site Administrator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 622
Offline Offline

Gender: Male
Posts: 3203


I haven't met a Jackpot that I didn't like!!!
« Reply #16 on: October 25, 2009, 06:27:29 PM »
Kevin,

I am curious about what this is: Sherlock Smiley Sherlock Smiley Sherlock Smiley

"From my limited Mikohn knowledge, the "extra" square board pictured between the main Supreme board and the display isn't needed, right?  (I'm assuming it had something to do with the MoneyTime link.)"

Can you post a good picture if it and the part number label....

CH CaptainHappy
Logged
  Come sail away, Come sail away Come sail away with me..
kenokarz
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 284
Offline Offline

Gender: Male
Posts: 470
« Reply #17 on: October 25, 2009, 07:51:12 PM »
yes back-up only, Duh! this way if insert one backwards i can remake the chip  muted
Logged
edski
Contributing Gold NLG Member
NLG Member 101 to 500 Post
*

Total Karma Storms: 123
Offline Offline

Gender: Male
Posts: 188
« Reply #18 on: October 25, 2009, 10:02:47 PM »
Quote from: CaptainHappy on October 25, 2009, 06:27:29 PM
Kevin,

I am curious about what this is: Sherlock Smiley Sherlock Smiley Sherlock Smiley

"From my limited Mikohn knowledge, the "extra" square board pictured between the main Supreme board and the display isn't needed, right?  (I'm assuming it had something to do with the MoneyTime link.)"

Can you post a good picture if it and the part number label....

CH CaptainHappy

Me too!

Need to see where all the wiring connects to the supreme and the machine.

Ed
Logged
Spoiled Rotten Birds
knagl
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 642
Offline Offline

Gender: Male
Posts: 5489


Kevin
« Reply #19 on: October 26, 2009, 01:34:16 AM »
Quote from: CaptainHappy on October 25, 2009, 06:27:29 PM
Can you post a good picture if it and the part number label....

Will do -- it'll be late Monday night before I have access to the pictures again (on a different computer), but I'll post as soon as I can.
Logged
If you find this site helpful, please consider making a small donation to help defray the cost of hosting and bandwidth.

Please do not PM me for support or "how to" requests -- please post your request in the forum so that everyone may assist you and everyone can benefit from the answer to your question!  Thanks! Smiley
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #20 on: October 26, 2009, 01:53:05 AM »
Well, For those of you that needed to see this in a larger than life-like form....
uh,...here it is again>>>

* 4096-chipmax.jpg (144.76 KB, 1024x1096 - viewed 617 times.)
Logged
stayouttadabunker
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 1039
Offline Offline

Gender: Male
Posts: 13447
« Reply #21 on: October 26, 2009, 01:54:11 AM »
 rotflmao That didn't work... Tongue Out
Just click on it to bring it out larger...
Logged
brichter
Spaced Alien
Senior Full time Member.
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 440
Offline Offline

Gender: Male
Posts: 2374



WWW
« Reply #22 on: October 26, 2009, 03:29:06 AM »
So, the supreme doesn't connect to the slot machine, it connects to a display (several different sizes are available) and a controller if you want to use it as a progressive display. The controller will hook up to the slot, and the hookup varies depending on the machine and the controller.

In standalone mode, it can provide text and graphics.

Here's what it looks like when interfaced with a CON2I and hooked up to a 1x3 display (note: the CON2I is providing all text and progressive info. Depending on the size of the display you attach to it, you can do graphics and animations also):

<a href="http://www.youtube.com/v/DDnJKUOWTZI&rel=0" target="_blank">http://www.youtube.com/v/DDnJKUOWTZI&rel=0</a>

I need to get off my dead butt and post the videos of my 2x3 display. arrow
« Last Edit: October 26, 2009, 03:35:24 AM by brichter » Logged
Thanks,
Bill
knagl
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 642
Offline Offline

Gender: Male
Posts: 5489


Kevin
« Reply #23 on: October 26, 2009, 04:12:15 PM »
Can anyone confirm for me that I would use the same serial cable I use for connecting my ChamII+ to PSP (a cable with pins 2, 3, and 5 straight through, with 1 and 5 jumpered on the Mikohn end) with this Supreme?
Logged
If you find this site helpful, please consider making a small donation to help defray the cost of hosting and bandwidth.

Please do not PM me for support or "how to" requests -- please post your request in the forum so that everyone may assist you and everyone can benefit from the answer to your question!  Thanks! Smiley
knagl
Global NLG Site Moderator
Sr.Tech NLG Member 1000+ Post
*

Total Karma Storms: 642
Offline Offline

Gender: Male
Posts: 5489


Kevin
« Reply #24 on: October 26, 2009, 04:18:48 PM »
Quote from: brichter on October 26, 2009, 03:29:06 AM
So, the supreme doesn't connect to the slot machine, it connects to a display (several different sizes are available) and a controller if you want to use it as a progressive display.

In standalone mode, it can provide text and graphics.

...and that's all we're hoping to do with the thing -- no progressive functions (yet) (we don't have a controller, anyway).  If the one in your video is a 1x3, is the one I posted on the first post of this thread a 1x1?  Also, I've seen some other pictures of the supreme boards and they have stickers on them indicating 1x2 or 1x3 -- is that a function of the board or the software on it?
Logged
If you find this site helpful, please consider making a small donation to help defray the cost of hosting and bandwidth.

Please do not PM me for support or "how to" requests -- please post your request in the forum so that everyone may assist you and everyone can benefit from the answer to your question!  Thanks! Smiley
Pages: [1] 2 3 4 5 Go Up Print 
« previous next »
Jump to:  

SimplePortal Classic 2.0.5

If you find this site helpful, Please Consider Making a small donation to help defray the cost of hosting and bandwidth.



Newlifegames.com ™    Newlifegames.net ™    Newlifegames.org ™
   New Life Games ™    NewLifeGames ™  NLG ™ We Bring new Life to old Games ™    1-888-NLG-SLOTS ™
Are all Copyright and Trademarks of New Life Games LLC 1992 - 2021


FAIR USE NOTICE:

This site contains copyrighted material the use of which has not always been specifically authorized by the copyright owner.
We make such material available in an effort to advance awareness and understanding of the issues involved.
We believe this constitutes a fair use of any such copyrighted material as provided for in section 107 of the US Copyright Law.
In accordance with Title 17 U.S.C. Section 107, the material on this site is distributed without profit to those
who have expressed a prior interest in receiving the included information for research and educational purposes.

For more information please visit: http://www.law.cornell.edu/uscode/17/107.shtml.

If you wish to use copyrighted material from this site for purposes of your own that go beyond fair use,
you must obtain permission directly from the copyright owner.

NewLifeGames.net Web-Site is optimized for use with Fire-Fox and a minimum screen resolution of 1280x768 pixels.


Powered by SMF 1.1.20 | SMF © 2013, Simple Machines
Loon Designed by Mystica
Updated by Runic Warrior
Page created in 0.135 seconds with 20 queries.